[多项选择] An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）
A. The switch that will share its VLAN configuration must be in VTP server mode.
B. The switches must be in the same VTP domain.
C. The switch that will share the VLAN information must be configured as the root bridge.
D. The switches must be connected over VLAN trunks.
E. The switches must be configured to use the same STP version.
F. The switches must have VTP pruning activated.

[多项选择]You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）
A. The switch name must match the workgroup name of the local network.
B. The switch must be configured with an IP address and default gateway.
C. The remote workstations must have access to the management VLAN of the switch.
D. CDP must be enabled on the switch so that it can be located by other devices on the network.

[单项选择] A Catalyst switch has just been installed and configured, and is not working as expected. You have decided to capture multiple show command outputs to study. Which one command could you use that includes the output of many other show commands, such as show version and show running-config?（）
A. show configuration
B. show memory
C. show stacks
D. show tech-support

[单项选择]On a Cisco Catalyst switch, which configuration command is used to apply a VACL named "test"to filter the traffic within VLAN100? （）
A. interface vlan 100 ip access-group test
B. interface vlan 100 ip access-group test in
C. interface vlan 100 ip access-group test out
D. vlan filter test vlan-list 100
E. vlan access-map test 100

[单项选择]You want your Catalyst switch to implement a switching method that holds a packet in its memory until the data portion of the respected packet reaches the switch.Which method should you employ on your Catalyst switch?（）
A. Fast Forward
B. Store and forward
C. Frag-free
D. None of the above

[单项选择]A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?（）
A. The switch port link lights will be off on both switches indicating the ports are not connected.
B. The switch port link light will be off on one switch indicating that STP has disabled the port.
C. The switch port link lights will flash amber indicating an error.
D. The switch port link lights will be green indicating normal operation.

[单项选择] A Cisco Catalyst switch is part of the CIS network. As an experienced network administrator, you are thinking of filtering the traffic within VLANI00 with the use of a VACL named "test" on that switch. Which of the following command will enable that?（）
A. interface vlan 100 ip access-group test in
B. interface vlan 100 ip access-group test
C. vlan access-map test 100
D. vlan filter test vlan-list 100

[单项选择] You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）
A. Switch(config)# switchport trunk encapsulation isl
B. Switch(config)# switchport trunk encapsulation ietf
C. Switch(config-if)# switchport trunk encapsulation isl
D. Switch(config-if)# switchport trunk encapsulation ietf
E. Switch(config-if)# switchport trunk encapsulation dot1q

[多项选择]By default, each port in a Cisco Catalyst switch is assigned to VLAN1. Which two recommendations are key to avoid unauthorized management access? （）
A. Create an additional ACL to block the access to VLAN 1.
B. Move the management VLAN to something other than default.
C. Move all ports to another VLAN and deactivate the default VLAN.
D. Limit the access in the switch using port security configuration.
E. Use static VLAN in trunks and access ports to restrict connections.
F. Shutdown all unused ports in the Catalyst switch.

[多项选择]An administrator is configuring one server to monitor hardware level information on a second Windows server.Which of the following should be setup on the Windows server to allow the monitoring server to access this information?（）
A. WMI
B. RIS
C. DNS
D. SNMP
E. SMTP

[单项选择] An administrator is configuring an LPAR for a NIM installation and is unsure if the 'Ping Test' option within SMS is a required configuration step. Which statement best describes the 'Ping Test' option?（）
A. The 'Ping Test' is a recommended step to verify the IP information entered into the RIPL SMS panel.
B. The 'Ping Test' is a mandatory step required to commit the IP information entered into the RIPL SMS panel.
C. The 'Ping Test' is an optional step to verify network configuration entered into the RIPL SMS panel on older copper-based networks.
D. The 'Ping Test' is an optional step to verify network connectivity between client and server, where ICMP traffic is allowed on the connecting network.

[多项选择]A network administrator is configuring ACLs on a cisco router,to allow traffic from hosts on networks 192.168.146.0,192.168.147.0,192.168.148.0and192.168.149.0 only.Which two ACL statements when combined are the best for accomplishing the task?（）
A. access-list 10 permit ip 192.168.147.0 0.0.0.255.255 
B. access-list 10 permit ip 192.168.149.0 0.0.0.255.255
C. access-list 10 permit ip 192.168.146.0 0.0.0.0.255
D. access-list 10 permit ip 192.168.146.0 0.0.0.1.255
E. access-list 10 permit ip 192.168.148.0 0.0.0.1.255
F. access-list 10 permit ip 192.168.146.0 255.255.255.0

[单项选择]An administrator is configuring IP 10.178.1.5 on a legacy device that will only accept a classfuladdress. Which of the following is the address that can be used in this scenario?（）
A. 10.178.1.5/1
B. 10.178.1.5/8
C. 10.178.1.5/16
D. 10.178.15/30

[单项选择]A network administrator must configure 200 switch ports to accept traffic from only the currently attached host devices. What would be the most efficient way to configure MAC-level security on all these ports?（）
A. Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command
B. Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command
C. Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them
D. Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security

[单项选择]On the Catalyst 6500 Series switch, which command is used to establish a console connection to the Firewall Services Module?（）
A. ssh
B. connect
C. login
D. session

[单项选择]A system administrator installed a new switch using a script to configure it. IP connectivity was tested using pings to SwitchB.Later attempts to access NewSwitch using Telnet from SwitchA faileD.Which statement is true?（）
A. Executing password recovery is required.
B. The virtual terminal lines are misconfigured.
C. Use Telnet to connect to RouterA and then to NewSwitch to correct the error.
D. Power cycle of NewSwitch will return it to a default configuration.