[单选题]
Refer to the exhibit. In the communication between host 1. and host 2. over the point-to-point WAN, which
Protocol or technology is represented by dashed line A?
A. IP
B. T1.
C. PPP
D. IEEE 802..3.

[单选题]
Refer to the exhibit. A network administrator attempts to ping Host2. from Host1. and receives the result that
Are shown. What is a possible problem?
A. The link between Host1. and Switch1. is down.
B. TCP/IP is not functioning on Host1..
C. The link between Router1. and Router2. is down.
D. The default gateway on Host1. is incorrect.
E. Interface Fa0./0. on Router1. is shudown.
F. The link between Switch1. and Router1. is down.

[单选题]
Refer to the topology and router output shown in the exhibit. A technician is troubleshooting host
Connectivity issues on the switches. The hosts in VLANs 10. and 15. on Sw11. are unable to communicate
With hosts in the same VLANs on Sw12.. Hosts in the Admin VLAN are able to communicate. The port-to-
VLAN assignments are identical on the two switches. What could be the problem?
A. The Fa0./1. port is not operational on one of the switches.
B. The Link connecting the switches has not been configured as a trunk.
C. At lease one port needs to be configured in VLAN 1. for VLANs 10. and 15. to be able to communicate.
D. Port FastEthernet 0./1. needs to be configured as an access link on both switches.
E. A router is required for hosts on Sw11. in VLANs 10. and 15. to communicate with hosts in the sameVLAN on Sw12..

[单选题]
Refer to the exhibit. An organization connect two locations, supporting two VLANs, through two switches as
Shown. Inter-VLANs communicated is not required. The network is working properly and there is fully
Connectivity. The organization needs to add additional VLANs, so it has been decided to implement VTP.
Both switches are configured as VTP servers in the same VTP domain. VLANs added to Switch1. are not
Learned by Switch2.. Based on this information and partial configuration is the exhibit, what is the problem?
A. Switch2. should be configured as a VTP client.
B. VTP is Cisco proprietory and requires a different trunking encapsulation
C. A router is required to route VTP advertisements between the swtiches.
D. STP has blocked on of the links between the switches, limiting connectivity.
E. The links between the switches are access links.

[单选题]
Refer to the exhibit,a network administrator cannot establish a telnet session with the indicated router.Whatis the cause of this failure?
A. A level 5. password is not set
B. The vty password is missing
C. The console password is missing
D. An ACL is blocking Telnet access

[单选题]
Refer to the exhibit. The network administrator is in a campus building distant from Building BWANRouter
Is hosting a newly installed WAN link on interface S0./0.. The new link is not functioning and the
Administrator needs to determine if the correct cable has been attached to the S0./0. interface. How can the
Administrator accurately verify the correct cable type on S0./0. in the most efficient manner?
A. Telnet to WANRouter and execute the command show interfaces S0./0.
B. Telnet to WANRouter and execute the command show processes S0./0.
C. Telnet to WANRouter and execute the command show running-configuration
D. Telnet to WANRouter and execute the command show controller S0./0.
E. Physically examine the cable between WANRouter S0./0. and the DCE.
F. Establish a console session on WANRouter and execute the command show interfaces S0./0.

[单选题]
Refer to the exhibit.
The network administrator has created a new VLAN on Switch1. and added host C and host DThe
Administrator has properly configured switch interfaces FastEthernet0./13. through FastEthernet0./24. to be
Members of the new VLAN. However, after the network administrator completed the configuration, host A
Could communicate with host
B, but host A could not communicate with host C or host DWhich
Commands are required to resolve this problem?
A. Router(config)# interface fastethernet 0./1..3.Router(config-if)# encapsulation dot1.q 3.
B. Router(config)# router rip
C. Switch1.# vlan databaseSwitch1.(vlan)# vtp v2.-modeSwitch1.(vlan)# vtp domain ciscoSwitch1.(vlan)# vtp server
D. Switch1.(config)# interface fastethernet 0./1.Switch1.(config-if)# switchport mode trunkSwitch1.(config-if)# switchport trunk encapsulation isl

[单选题]
Refer to the exhibit. Which statement describes DLCI 17.?
A. DLCI 17. describes the ISDN circuit between R2. and R3..
B. DLCI 17. describes a PVC on R2.. It cannot be used on R3. or R1..
C. DLCI 17. is the Layer 2. address used by R2. to describe a PVC to R3..
D. DLCI 17. describes the dial-up circuit from R2. and R3. to the service provider.

[单选题]
Refer to the exhibit. How should the FastEthernet0./1. port on the 295.0. model switches that are shown in the
Exhibit be configured to allow connectivity between all devices?
A. The ports only need to be connected by a crossover cable.
B. SwitchX(config)# interface FastEthernet 0./1.SwitchX(config-if)# switchport mode trunk
C. SwitchX(config)# interface FastEthernet 0./1.SwitchX(config-if)# switchport mode accessSwitchX(config-if)# switchport access vlan 1.
D. SwitchX(config)# interface FastEthernet 0./1.SwitchX(config-if)# switchport mode trunkSwitchX(config-if)# switchport trunk vlan 1.SwitchX(config-if)# switchport trunk vlan 10.SwitchX(config-if)# switchport trunk vlan 20.

[单选题]
Refer to the exhibit. What statement is true of the configuration for this network?
A. The configuration that is shown provides inadequate outside address space for translation of thenumber of inside addresses that are supported.
B. Because of the addressing on interface FastEthernet0./1., the Serial0./0. interface address will not supportthe NAT configuration as shown.
C. The number 1. referred to in the ip nat inside souce command recerences access-list number 1..

[单选题]
Refer to the exhibit. The company uses EIGRP as the routing protocol. What path will packets take from a
A. The path of the packets will be R3. to R2. to R1..
B. The path of the packets will be R3. to R1. to R2..
C. The path of the packets will be both R3. to R2. to R1. and R3. to R1..
D. The path of the packets will be R3. to R1.

[单选题]
Refer to the exhibit. A network associate has configured the internetwork that is shown in the exhibit, but
Has failed to configure routing properly.
Which configuration will allow the hosts on the Branch LAN to access resources on the HQ LAN with the
Least impact on router processing and WAN bandwidth?
A. HQ(config)# router ripBranch(config)# router rip
B. HQ(config)# router eigrp 56Branch(config)# router eigrp 56.
C. HQ(config)# router ospf 1Branch(config)# router ospf 1

[单选题]
Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit
Represents this design, with all hosts configured in the same VLAN. What conclusions can be made about
This design?
A. The design will function as intended
B. Spanning-tree will need to be used.
C. The router will not accept the addressing scheme.
D. The connection between switches should be a trunk.
E. The router interfaces must be encapsulated with the 802..1.Q protocol.

[单选题]
Refer to the exhibit. What type of connection would be supported by the cable diagram shown?
A. PC to router
B. PC to switch
C. server to switch
D. switch to router

[单选题]
Refer to the exhibit. Which of these statements correctly describes the state of the switch once the boot
Process has been completed?
A. Only the default VLANs are configured on SwitchA.
B. SwitchA does not have a VTP domain name configured.
C. VTP pruning needs to be enabled on SwitchA.
D. SwitchC needs to have the VTP domain name configured.
E. SwitchB is in transparent mode.