[单选题]
Refer to the exhibit. A network administrator attempts to ping Host2. from Host1. and receives the result that
Are shown. What is a possible problem?
A. The link between Host1. and Switch1. is down.
B. TCP/IP is not functioning on Host1..
C. The link between Router1. and Router2. is down.
D. The default gateway on Host1. is incorrect.
E. Interface Fa0./0. on Router1. is shudown.
F. The link between Switch1. and Router1. is down.

[单选题]
Refer to the exhibit. A network administrator needs to add a new VLAN, named VLAN3., to the network
Shown. Unfortunately, there is not another FastEthernet interface on R1. to connect to the new VLAN3..
Which approach is the most cost effective solution for this problem?
A. Purchase a new FastEthernet module and install it on R1.
B. Replace R1. with a new router that has at least three FastEthernet interfaces.
C. Configure a second switch to support VLAN3. with a VLAN trunk between SW1. and the new switch.
D. Configure a single VLAN trunk between R1. and SW1. and configure subinterface on R1. interface foreach VLAN.
E. Connect another router to a serial interface of R1.. Use a FastEthernet interface on the new router for
VLAN3..

[单选题]
Refer to the exhibit,a network administrator cannot establish a telnet session with the indicated router.Whatis the cause of this failure?
A. A level 5. password is not set
B. The vty password is missing
C. The console password is missing
D. An ACL is blocking Telnet access

[单选题]
The network administrator has discovered that the power supply has failed on a switch in the company LAN
And that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 295.0. series switch.
What must be done to ensure that this new switch becomes the root bridge on the network?
A. Lower the bridge priority number.
B. Change the MAC address of the switch.
C. Increase the VTP revision number for the domain.
D. Lower the root path cost on the switch ports.
E. Assign the switch an IP address with the lowest value.

[单选题]
A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP
Addresses of the devices with which the router has established adjacency. The retransmit interval and the
Queue counts for the adjacent routers also need to be checked. What command will display the required
Information?
A. Router# show ip eigrp adjacency
B. Router# show ip eigrp topology
C. Router# show ip eigrp interfaces
D. Router# show ip eigrp neighbors

[单选题]
A network administrator is troubleshooting the OSPF configuration of routers R1. and R2.. The routers
Cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of
The show ip ospf interface e0. command for routers R1. and R2.. Based on the information in the graphic,
What is the cause of this problem?
A. The OSPF area is not configured properly.
B. The priority on R1. should be set higher.
C. The cost on R1. should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.

[单选题]
Refer to the exhibit. The network administrator is in a campus building distant from Building BWANRouter
Is hosting a newly installed WAN link on interface S0./0.. The new link is not functioning and the
Administrator needs to determine if the correct cable has been attached to the S0./0. interface. How can the
Administrator accurately verify the correct cable type on S0./0. in the most efficient manner?
A. Telnet to WANRouter and execute the command show interfaces S0./0.
B. Telnet to WANRouter and execute the command show processes S0./0.
C. Telnet to WANRouter and execute the command show running-configuration
D. Telnet to WANRouter and execute the command show controller S0./0.
E. Physically examine the cable between WANRouter S0./0. and the DCE.
F. Establish a console session on WANRouter and execute the command show interfaces S0./0.

[单选题]
A network administrator is verifying the configuration of a newly installed host by establishing an FTP
Connection to a remote server. What is the highest layer of the protocol stack that the nework administrator
Is using for this operation?
A. application
B. presentation
C. session
D. transport
E. internet
F. data link

[多选题]A network administrator changes the configuration register to 0.x214.2. and reboots the router. What are tworesults of making this change? (Choose two.)
A. The IOS image will be ignored.
B. The router will prompt to enter initial configuration mode.
C. The router will boot to ROM.
D. Any configuration entries in NVRAM will be ignored.
E. The configuration in flash memory will be booted.

[单选题]
Which command helps a network administrator to manage memory by displaying flash memory andNVRAM utilization?
A. show secure
B. show file systems
C. show flash
D. show version

[单选题]
A network administrator needs to configure a serial link between the main office and a remote location.The
Router at the remote office is a non-cisco router. How should the network administrator configure the serial
Interface of the main office router to make the connection?
A. Main(config)#interface serial 0./0.Main(config-if)#no shut
B. Main(config)#interface serial 0./0.Main(config-if)#encapsulation ietfMain(config-if)#no shut
C. Main(config)#interface serial 0./0.Main(config-if)#encapsulation frame-relayMain(config-if)#authenication chapMain(config-if)#no shut
D. Main(config)#interface serial 0./0.Main(config-if)#encapsulation pppMain(config-if)#no shut

[单选题]
Refer to the exhibit. A network associate has configured the internetwork that is shown in the exhibit, but
Has failed to configure routing properly.
Which configuration will allow the hosts on the Branch LAN to access resources on the HQ LAN with the
Least impact on router processing and WAN bandwidth?
A. HQ(config)# router ripBranch(config)# router rip
B. HQ(config)# router eigrp 56Branch(config)# router eigrp 56.
C. HQ(config)# router ospf 1Branch(config)# router ospf 1

[单选题]
Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit
Represents this design, with all hosts configured in the same VLAN. What conclusions can be made about
This design?
A. The design will function as intended
B. Spanning-tree will need to be used.
C. The router will not accept the addressing scheme.
D. The connection between switches should be a trunk.
E. The router interfaces must be encapsulated with the 802..1.Q protocol.

[单选题]
Refer to the exhibit. The network manager is evaluating the efficiency of the current network design. RIPv2.
Is enabled on all Layer 3. devices in the network. What network devices participate in passing traffic from
Destination?
A. Switch1., Switch2.
B. Switch1., Switch2., Switch2., Switch2.
C. Switch1., Router1., Switch1., Switch2.
D. Switch1., Router1., Router2., Switch2.

[多选题]
Refer to the exhibit.The network administrator requires easy configuration options and minimal routing
Protocol traffic.Which two options provide adequate routing table information for traffic that passes between
The two routers and satisfy the requests of the network administrator?(choose two)
A. a dynamic routing procotol on InternetRouter to advertise summarized routers to CentralRouter.
B. a dynamic routing procotol on CentralRouter to advertise summarized routers to InternetRouter.
C. a dynamic routing procotol on InternetRouter to advertise all routes to CentralRouer.
D. a dynamic routing procotol on CentralRouer to advertise all routes to InternetRouter
E. a static,default route on CentralRouter that directs traffic to InternetRouter.