[单选题]
Refer to the exhibit. What statement is true of the configuration for this network?
A. The configuration that is shown provides inadequate outside address space for translation of thenumber of inside addresses that are supported.
B. Because of the addressing on interface FastEthernet0./1., the Serial0./0. interface address will not supportthe NAT configuration as shown.
C. The number 1. referred to in the ip nat inside souce command recerences access-list number 1..

[单选题]
Which statement is true?
A. An IPv6. address is 64. b long and is represented as hexadecimal characters.
B. An IPv6. address is 32. b long and is represented as decimal digits.
C. An IPv6. address is 128. b long and is represented as decimal digits.
D. An IPv6. address is 128. b long and is represented as hexadecimal characters.

[单选题]
Of the following statement is true concering this command?
A. The broadcast option allows packets,such as RIP updates,to be forwarded access the PVC.
B. The command shoud be executed from the goble configuration mode.
C. 102. is he remote DLCI that will recive the information.
D. This command is required for all Frame Rely configurations

[单选题]
Which statement about RIPng is true?
A. RIPng allows for routes with up to 30. hops.
B. RIPng is enabled on each interface separately.
C. RIPng uses broadcasts to exchange routes.
D. There can be only one RIPng process per router.

[单选题]
Which statement is true, as relates to classful or classless routing?
A. Automatic summarization at classful boundries can cause problems on discontinuous subnets
B. EIGRP and OSPF are classful routing protocols and summarize routes by default
C. RIPv1. and OSPF are classless routing protocols
D. Classful routing protocols send the subnet mask in routing updates

[单选题]
Refer to the exhibit. Which statement describes DLCI 17.?
A. DLCI 17. describes the ISDN circuit between R2. and R3..
B. DLCI 17. describes a PVC on R2.. It cannot be used on R3. or R1..
C. DLCI 17. is the Layer 2. address used by R2. to describe a PVC to R3..
D. DLCI 17. describes the dial-up circuit from R2. and R3. to the service provider.

[单选题]
Which statement about IPv6. is true?
A. Addresses are not hierarchical and are assigned at random.
B. Only one IPv6. address can exist on a given interface.
C. There are 2..7. billion addresses available.
D. Broadcasts have been eliminated and replaced with multicasts.

[单选题]What is true about people with colorblindness?
A.They have fewer cone-shaped cells than other people.
B.They are not interested in colorful stuff.
C.They can recognize 1 million different colors.
D.They may find daily tasks more difficult.

[单选题]
Refer to the exhibit. What can be determined about the router from the console output?
A. No configuration file was found in NVRAM.
B. No configuration file was found in flash.
C. No configuration file was found in the PCMCIA card.
D. Configuration file is normal and will load in 15. seconds.

[单选题]
Refer to the exhibit. What type of connection would be supported by the cable diagram shown?
A. PC to router
B. PC to switch
C. server to switch
D. switch to router

[多选题]Refer to the exhibit. What could be possible causes for the "Serial0./0. is down" interface status? (Choosetwo.)
A. A Layer 1. problem exists.
B. The bandwidth is set too low.
C. A protocol mismatch exists.
D. An incorrect cable is being used.
E. There is an incorrect IP address on the Serial 0./0. interface.

[单选题]
Refer to the exhibit. What will happen to HTTP traffic coming from the Internet that is destined for
A. Traffic will be dropped per line 30. of the ACL.
B. Traffic will be accepted per line 40. of the ACL.
C. Traffic will be dropped, because of the implicit deny all at the end of the ACL.
D. Traffic will be accepted, because the source address is not covered by the ACL.

[单选题]
Refer to the diagram. What is the largest configuration file that can be stored on this router?
A. 191.K bytes
B. 163.84.K bytes
C. 313.69.K bytes
D. 114.688.K bytes

[单选题]
Refer to the exhibit. What is the meaning of the output MTU 150.0. bytes?
A. The maximum number of bytes that can traverse this interface per second is 150.0..
B. The minimum segment size that can traverse this interface is 150.0. bytes.
C. The minimum segment size that can traverse this interface is 150.0. bytes.
D. The minimum packet size that can traverse this interface is 150.0. bytes.
E. The maximum packet size that can traverse this interface is 150.0. bytes.
F. The maximum frame size that can traverse this interface is 150.0. bytes.

[单选题]
Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol
Down”?
A. There is a mismatch in encapsulation types
B. The wrong type of cable is connected to the interface
C. The interface has been configured with the shutdown command
D. The interface is not receiving any keepalives
E. The interface needs to be configured as a DTE device
F. There is no encapsulation type configured

[多选题]
Refer to the exhibit. What commands must be configured on the 295.0. switch and the router to allowcommunication between host 1. and host 2.? (Choose two.)
A. Router(config)# interface fastethernet 0./0.Router(config-if)# no shut down
B. Router(config)# interface fastethernet 0./0.Router(config-if)# no shut downRouter(config)# interface fastethernet 0./0..1.Router(config-subif)# encapsulation dot1.q 10.Router(config-subif)# interface fastethernet 0./0..2.Router(config-subif)# encapsulation dot1.q 20.
C. Router(config)# router eigrp 100.
D. Switch1.(config)# vlan databaseSwitch1.(config-vlan)# vtp domain XYZSwitch1.(config-vlan)# vtp server
E. Switch1.(config)# interface fastethernet 0./1.Switch1.(config-if)# switchport mode trunk
F. Switch1.(config)# interface vlan 1.

[单选题]
Refer to the exhibit.What is the effect of the configuration that is shown?
A. It tells the router or switch to try establish an SSH connection first and if that fail to use telnet.
B. Itconfigures a cisco network device to use the SSH protocol on incoming communications via the virtualterminal ports.
C. It allows seven failed login attempts before the VTY lines are temporarily shutdown.
D. It configures SSH globally for all logins.

[单选题]
Refer to the exhibit.What is the result of setting the no login command?
A. The is a virtually limitless supply of IP addresses
B. Telnet access requires a new password at first login
C. Telnet access requires a password
D. Telnet access is denied

[多选题]
Refer to the exhibit.What two results would occur if the hub were to be replaced with a switch that is
Configured with one Ethernet VLAN?(choose two)
A. The number of collision domains would decrease.
B. The number of collision domains would increase.
C. The number of broadcast domains would remain the same.
D. The number of collision domains would remain the same.
E. The number of broadcast domains would increase.