更多"[多选题]关于GGSN system-user的配置，下面说法正确的是"的相关试题:
[多选题]关于GGSN的NTP配置，下面说法正确的是（）。
About GGSN NTP configuration, which statements are correct?
A.ntp server vrf mng配置了NTP时钟源地址
NTP server vrf mng should have configured NTP resource ip address
B.ntp source配置了xgw管理口地址
NTP source should have configured xGW management interface address.
C.ntp enable
D.ntp destination配置了时钟源地址
NTP destination should have configured ntp resource ip address
[多选题]关于GGSN的CPU配置，下面说法正确的是（）。
About GGSN CPU configuration, which statement is correct?
A.CSU 单板CPU0作为SLB模块，CPU2作为CU模块。
CPUO of CSU board should be SLB module and CPU2 should be CU module.
B.SLB单板两个CPU禁止配置成处理业务CPU组，只进行信令消息分担转发处理。
SLB board can not configured as service CPU group, it only work for the signal load balance and transmission process.
C.GSU和SLB单板的CPU配置1+1备份方式，CU无备份。
GSU and SLB works in 1+1 backup mode, CU without backup mode.
D.GSU/CU组和SLB CPU组查询结果CPU的Appstatus为Master/Slave状态关系。
The appstatus of GSU,CU,SLB group should be master/slave.
[单选题]关于GGSN的CPU配置，下面说法不正确的是（）。
Which of the following statements is incorrect about CPU configurations of the GGSN? ( )
A.CSU 单板CPU0作为SLB模块，CPU2作为CU模块。
CPUO of the CSU board is used as the SLB module and CPU2 is used as the CU module.
B.SLB单板两个CPU禁止配置成处理业务CPU组，只进行信令消息分担转发处理。
The two CPUs on the SLB board are forbidden to be configured as a service processing CPU group, and they only balance and forward signaling messages.
C.GSU和SLB单板的CPU配置1+1备份方式，CU无备份。
CPUs of the GSU board and the SLB board are configured in 1+1 backup mode, and the CU works in no backup mode.
D.GSU/CU组和SLB CPU组查询结果CPU的Appstatus为Master/Slave状态关系。
According to the GSU/CU group and SLB CPU group query results, the Appstatus of the CPU is master/slave.
[多选题]GGSN的FTP配置，下面说法正确的是（）。
About GGSN FTP configuration, which statement is correct?
A.ftp-server为enable
ftp-server enable
B.ftp-type为FTP或SFTP
FTP-type should be FTP or SFTP
C.用sh ftp-server查看FTP配置
Use "show ftp-server" to check the FTP configuration
D.ftp-server为disable
FTP-SERVER should be configured to disable
[多选题]关于GGSN的IP地址、路由配置，下面说法正确的是（）。
About the GGSN ip address and route configuration, which statement is correct?
A.子接口的MAC偏移需要与父接口不能一样。
mac offset of subinterface can not be same with the located interface.
B.PFU对外物理接口端口模式需要和互联设备端口模式一致，速率、协商模式双方必须一样。
PFU interface must keep consistent with peer interface on mode, speed, negotiated mode.
C.PFU物理端口配置必须有端口描述，便于数据核查和日常维护。
PFU physical interface must have the interface description so that we can do data check and daily maintenance.
D.根据组网规划指导要求，设备开局网络规划必须是双平面,不允许有单点故障，开局中要进行组网倒换测试。
According to the network design rules, the network must be dual network. Single point trouble is forbidden and network switchover test should be done when commissioning.
[多选题]关于GGSN与OCS的互联配置，下面说法正确的是（）。
About interconnection configuration between GGSN and OCS, which of the following statements are correct? ( )
A.配置本局节点
Configure local node
B.配置邻接局节点
Configure adjacent node
C.配置TCP链路
Configure TCP link
D.配置diameter链路
Configure diameter link
[单选题]关于GGSN system-user的配置，下面说法不正确的是（）。
Which of the following statements is wrong about system-user configuration on the GGSN? ( )
A.需要配置了authentication-template。
The authentication-template needs to be configured.
B.不需要配置了authorization-template。
The authorization-template does not need to be configured.
C.需要配置了default-privilege-level。
The default-privilege-level needs to be configured.
D.需要配置了登录帐户。
The login account needs to be configured.
[单选题]关于GGSN的IP地址、路由配置，下面说法不正确的是（）。
Which of the following statements is wrong about IP address and route configurations on the GGSN? ( )
A.子接口的MAC偏移需要与父接口不能一样。
MAC offset of the sub-interface cannot be the same as that of the parent interface.
B.PFU对外物理接口端口模式需要和互联设备端口模式一致，速率、协商模式双方必须一样。
The port mode, rate, and negotiation mode should be completely the same between the external physical interface of the PFU and the interconnected device.
C.PFU物理端口配置必须有端口描述，便于数据核查和日常维护。
The physical port of the PFU must have the corresponding interface description, to facilitate data checking and daily maintenance.
D.根据组网规划指导要求，设备开局网络规划必须是双平面,不允许有单点故障，开局中要进行组网倒换测试。
According to requirements of networking planning, the network must be a dual-plane network, with no single-point fault. During office commissioning, we should carry out network switchover tests.
[多选题]关于GGSN的IP地址、路由配置的检查，下面说法正确的是（）。
About the GGSN ip address and route configuration, which statements are correct?
A.GTP,SLB,Radius客户端地址,Cg Agent,Diameter，L2TP等业务地址地址配置在Loopback接口上。
need to configure GTP,SLB,Radius client,Cg Agent,Diameter，L2TP service ip address on loopback interface.
B.同一个VRF下的IP地址，配置在同一个loopback下，一个loopback下配置的IP地址不超过16个。
When the ip address is under the same VRF, should configure those ip on one loopback interface and one loopback interface can support 16 ip address at maximum.
C.PFU物理端口配置必须有端口描述，便于数据核查和日常维护。
PFU physical interface must have the interface description so that we can do data check and daily maintenance.
D.子接口的MAC偏移需要与父接口保持一致。
mac offset of subinterface should be the same with the located interface.
[多选题]GGSN上线之前，需要检查SNMP配置，下面说法正确的是（）。
Before online GGSN, need to check the SNMP configuration, which statements are correct?
A.snmp-server host vrf mng 配置了EMS的地址。
Configure the EMS ip address in snmp-server host vrf mng.
B.snmp-server trap-source配置了xGW的管理口地址。
Configure the xGW manager interface ip in snmp-server trap-source.
C.snmp-server community配置了读串和写串。
Configure the read&write string in snmp-server community.
D.snmp-server user配置了不同权限的用户。
Configure the users with different kind of privilege.
[单选题]GGSN上线之前，需要检查SNMP配置，下面说法不正确的是（）。
Before the GGSN system gets online, we need to check SNMP configurations. Which of the following statements is correct? ( )
A.snmp-server host vrf mng 配置了EMS的地址。
Set "snmp-server host vrf mng" to the IP address of the EMS.
B.snmp-server trap-source配置了xGW的管理口地址。
Set "snmp-server trap-source" to the IP address of the management on the xGW.
C.snmp-server community配置了读串和写串。
Set "snmp-server community" to reading and writing strings.
D.snmp-server user配置了不同权限的用户。
Set "snmp-server user" to users with different rights.
[单选题]GGSN本地配置下发的地址池类型分配方式（）。
When the GGSN assigns IP addresses locally, when IP pool allocation mode configured on the GGSN is ( ).
A.aaa
B.assigned
C.dhcp
D.local
[单选题]关于商用局GGSN的组网情况，下面说法不正确的是（）。
Which of the following statements is incorrect about the networking structure of the GGSN in a commercial office? ( )
A.推荐采用GN，GI口采用静态路由来保证传输的可靠性。
It is recommended that GN and Gi interfaces use static routes to ensure transmission reliability.
B.Gn、Ga、Gi（net、wap）路由必须分布在不同PFU单板的实接口。
Routes of Gn, Ga, and Gi (net, wap) interfaces should be located on real interfaces of different PFU boards.
C.一块PFU单板拔出后，路由能够自动切换到另一块PFU单板物理接口。
When one PFU board is removed, its route can automatically switch over to the physical interface of another PFU board.
D.若采用OSPF发布地址段时，需要确认内部每段地址都已经发布出去。
While using the OSPF to distribute address segments, we need to confirm that each internal IP segment has been distributed successfully.
[多选题]关于商用局GGSN的组网情况，下面说法正确的是（）。
Which of the following statements are correct about the networking structure of the SGSN in commercial offices? ( )
A.推荐采用GN,GI口采用静态路由来保证传输的可靠性。
It is recommended that GN,Gi interfaces use the static route to ensure transmission reliability.
B.Gn、Ga、Gi（net、wap）路由必须分布在不同PFU单板的实接口。
Routes of Gn, Ga, and Gi (net, wap) interfaces should located on different PFU physical interface.
C.一块PFU单板拔出后，路由能够自动切换到另一块PFU单板物理接口。
When one PFU board was unplugged, the route should switch over to another PFU board automatically.
D.若采用OSPF发布地址段时，需要确认内部每段地址都已经发布出去。
If use the ospf to distribute the IP segment, make sure every network IP segment has been distributed successfully.
[判断题]xGW GGSN修改配置立即生效，完成配置后必须执行存盘命令。
A.正确
B.错误
[单选题]xGW GGSN中，关于CU，说法不正确的是（ ）。
In the xGW GGSN, which of the following statements is wrong about the CU? ( )
A.CU固定配置在CSU单板的2号CPU上
The CU is fixed on CPU2 of the CSU board.
B.一个GGSN网元需要配置两个CU Group
One GGSN NE needs to be configured with two CU groups.
C.CU工作方式是1+1主备
The CU works in 1+1 active/standby working mode.
D.CU具有话单缓存功能
The CU has the CDR caching function.
[多选题]在V4 GGSN中，需要配置下面哪些接口的loopback地址？（）
On V4 GGSN, the following interfaces should be configured with the loopback address: ( ).
A.GTPC
B.radius client
C.GTPU
D.cgagent
