更多"[多选题]Refer to the exhibit. The outp"的相关试题:
[单选题]
Refer to the topology and router output shown in the exhibit. A technician is troubleshooting host
Connectivity issues on the switches. The hosts in VLANs 10. and 15. on Sw11. are unable to communicate
With hosts in the same VLANs on Sw12.. Hosts in the Admin VLAN are able to communicate. The port-to-
VLAN assignments are identical on the two switches. What could be the problem?
A. The Fa0./1. port is not operational on one of the switches.
B. The Link connecting the switches has not been configured as a trunk.
C. At lease one port needs to be configured in VLAN 1. for VLANs 10. and 15. to be able to communicate.
D. Port FastEthernet 0./1. needs to be configured as an access link on both switches.
E. A router is required for hosts on Sw11. in VLANs 10. and 15. to communicate with hosts in the sameVLAN on Sw12..
[多选题]
Refer to the partial command output shown. Which two statements are correct regarding the router
Hardware? (Choose two.)
A. Total RAM size is 32. KB.
B. Total RAM size is 163.84. KB (16. MB).
C. Total RAM size is 655.36. KB (64. MB).
D. Flash size is 32. KB.
E. Flash size is 163.84. KB (16. MB).
F. Flash size is 655.36. KB (64. MB).
[单选题]
Refer to the exhibit. Give this output for SwitchC, what should the network administrator's next action be?
A. Check the trunk encapsulation mode for SwitchC's fa0./1. port.
B. Check the duplex mode for SwitchC's fa0./1. port.
C. Check the duplex mode for SwitchA's fa0./2. port.
D. Check the trunk encapsulation mode for SwitchA's fa0./2. port.
[单选题]
The output of the show frame-relay pvc command shows "PVC STATUS=INACTIVE". What does thismean?
A. The PVC is configured correctly and is operating normally, but no data packets have been detected formore than five minutes.
B. The PVC is configured correctly, is operating normally, and is no longer actively seeking the addressthe remote route.
C. The PVC is configured correctly, is operating normally, and is waiting for interesting to trigger a call tothe remote router.
D. The PVC is configured correctly on the local switch, but there is a problem on the remote end of thePVC.
E. The PVC is not configured on the switch.
[单选题]
Which line from the output of the show ip interface command indicates a layer 1. problem?
A. Serial0./1. is up, line protocol is down
B. Serial0./1. is down, line protocol is down
C. Serial0./1. is up, line protocol is up
D. Serial0./1. is administratively down, line protocol is down
[单选题]
Refer to the exhibit. The show vtp status command is executed at a switch that is generating the exhibitoutput. Which statement is true for this switch?
A. The switch forwards its VLAN database to other switches in the ICND VTP domain.
B. The configuration revision number increments each time the VLAN database is updated.
C. The switch forwards VTP updates that are sent by other switches in the ICND domain.
D. The VLAN database is updated when VTP information is received from other switches.
[单选题]
Refer to the exhibit. An organization connect two locations, supporting two VLANs, through two switches as
Shown. Inter-VLANs communicated is not required. The network is working properly and there is fully
Connectivity. The organization needs to add additional VLANs, so it has been decided to implement VTP.
Both switches are configured as VTP servers in the same VTP domain. VLANs added to Switch1. are not
Learned by Switch2.. Based on this information and partial configuration is the exhibit, what is the problem?
A. Switch2. should be configured as a VTP client.
B. VTP is Cisco proprietory and requires a different trunking encapsulation
C. A router is required to route VTP advertisements between the swtiches.
D. STP has blocked on of the links between the switches, limiting connectivity.
E. The links between the switches are access links.
[单选题]
Refer to the exhibit. A network administrator attempts to ping Host2. from Host1. and receives the result that
Are shown. What is a possible problem?
A. The link between Host1. and Switch1. is down.
B. TCP/IP is not functioning on Host1..
C. The link between Router1. and Router2. is down.
D. The default gateway on Host1. is incorrect.
E. Interface Fa0./0. on Router1. is shudown.
F. The link between Switch1. and Router1. is down.
[单选题]
Refer to the exhibit,a network administrator cannot establish a telnet session with the indicated router.Whatis the cause of this failure?
A. A level 5. password is not set
B. The vty password is missing
C. The console password is missing
D. An ACL is blocking Telnet access
[单选题]
Refer to the exhibit.
The network administrator has created a new VLAN on Switch1. and added host C and host DThe
Administrator has properly configured switch interfaces FastEthernet0./13. through FastEthernet0./24. to be
Members of the new VLAN. However, after the network administrator completed the configuration, host A
Could communicate with host
B, but host A could not communicate with host C or host DWhich
Commands are required to resolve this problem?
A. Router(config)# interface fastethernet 0./1..3.Router(config-if)# encapsulation dot1.q 3.
B. Router(config)# router rip
C. Switch1.# vlan databaseSwitch1.(vlan)# vtp v2.-modeSwitch1.(vlan)# vtp domain ciscoSwitch1.(vlan)# vtp server
D. Switch1.(config)# interface fastethernet 0./1.Switch1.(config-if)# switchport mode trunkSwitch1.(config-if)# switchport trunk encapsulation isl
[单选题]
Refer to the exhibit. The network administrator is in a campus building distant from Building BWANRouter
Is hosting a newly installed WAN link on interface S0./0.. The new link is not functioning and the
Administrator needs to determine if the correct cable has been attached to the S0./0. interface. How can the
Administrator accurately verify the correct cable type on S0./0. in the most efficient manner?
A. Telnet to WANRouter and execute the command show interfaces S0./0.
B. Telnet to WANRouter and execute the command show processes S0./0.
C. Telnet to WANRouter and execute the command show running-configuration
D. Telnet to WANRouter and execute the command show controller S0./0.
E. Physically examine the cable between WANRouter S0./0. and the DCE.
F. Establish a console session on WANRouter and execute the command show interfaces S0./0.
[单选题]
Refer to the exhibit. Which statement describes DLCI 17.?
A. DLCI 17. describes the ISDN circuit between R2. and R3..
B. DLCI 17. describes a PVC on R2.. It cannot be used on R3. or R1..
C. DLCI 17. is the Layer 2. address used by R2. to describe a PVC to R3..
D. DLCI 17. describes the dial-up circuit from R2. and R3. to the service provider.
[单选题]
Refer to the exhibit. The user at Workstation B reports that Server A cannot be reached. What is
Preventing Workstation B from reaching Server A?
A. The IP address for Server A is a broadcast address.
B. The IP address for Workstation B is a subnet address.
C. The gateway for Workstation B is not on the same subnet.
D. The gateway for Server A is not on the same subnet.
[单选题]
Refer to the exhibit. A network associate has configured the internetwork that is shown in the exhibit, but
Has failed to configure routing properly.
Which configuration will allow the hosts on the Branch LAN to access resources on the HQ LAN with the
Least impact on router processing and WAN bandwidth?
A. HQ(config)# router ripBranch(config)# router rip
B. HQ(config)# router eigrp 56Branch(config)# router eigrp 56.
C. HQ(config)# router ospf 1Branch(config)# router ospf 1