[单选题]
A switch is configured with all ports assigned to vlan 2. with full duplex FastEthernet to segment existing
Departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?
A. More collision domains will be created.
B. IP address utilization will be more efficient.
C. More bandwidth will be required than was needed previously.
D. An additional broadcast domain will be created.

[多选题]
Switch ports operating in which two roles will forward traffic according to the IEEE 802..1.w standard?(Choose two.)
A. alternate
B. backup
C. designated
D. disabled
E. root

[单选题]
VLAN 3. is not yet configured on your switch.What happens if you set the switchport access vlan 3.commmand interface configuration mode?
A. The command is accepted and the respective VLAN is added to vlan dat.
B. The command is rejected.
C. The command is accepted and you must configure the VLAN manually.
D. The port turns amber.

[单选题]
A switch is configured as a vtp sever with a domain name of CCNA.Which cisco ios privileged mode
Command,followed by a reload of the swith,will reset the VTP management domain name of the switch to a
NULL value?
A. #vtp domain unset
B. #delete vlan.dat
C. #no vtp domain
D. #vtp domain null

[单选题]
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.
OSPF has been configured on the router,as the routing protocol for the network.Which statement about this
Network is true?
A. For the two vlans to communicate,a network statement for the trunk interface needs to be added to theOSPF configuration.
B. For the two vlans to communicate,a network statement for each subinterface needs to be added to theOSPF configuration.
C. Direct inter-vlan communication does not require OSPF.
D. OSPF cannot be used if router-on-a-stick is configured on the router.

[单选题]
Which sequence of commands will configured RIPv2. on router B?
A. B(config)# router ripB(config-router)# version 2B(config-router)# end
B. B(config)# router ripB(config-router)# end
C. B(config)# router ripB(config-router)# version 2B(config-router)# end
D. B(config)# router rip version 2B(config-router)# end

[单选题]61 An LTM device configured with a management IP address and route and a series of self-IPs and TMM routes. Both management and TMM have a routing entry for 101 10/24 Application traffic is being load balanced and sent to pool member 10.1.1.123 with SNAT Automap and configured.
Which route will the LTM device use?
A.TMM route regardless of the management port status
B.both routes, which will duplicate traffic on both management and TMM interface
C.equal cost multipath load balancing via both routes
D.management route when TMM interface is down or TMM is offline
E.management route regardless of the management port status

[单选题]32 RADIUS authentication has been configured on the LTM device. The default remote user access requirements are as shown:
Read only access to the configuration Utility Access to TMOS shell
Which two items need to be configured in this situation? (Choose two)
A.Console access is Advanced Shell
B.Console access is Read Only
C.Default remote user role is Guest
D.In Console access is TMSH
E.Default remote user role is Manager
F.Default remote user role is Operator

[多选题]59 A virtual server is configured to handle https traffic. The clientssl profile is configured to use a2048-bit RSA key. Due to security requirements, is the LTM Specialist needs to use a 4096-bit RSA key in the future.
What two effects will this change have on the BIG-IP device? (Choose two)
A.Increase of CPU usage on the BIG-IP device
B.Decrease to 20% of licensed TPS
C.Decrease to 90% of licensed TPS
D.Increased of concurrent connection on client-side
E.Increase of TLS Renegotiation

[单选题]124 An LTM device needs to be configured a virtual server. The application requires SSL encryption from the client to the server and an X-Forwarded-For added by the LTM device. Which virtual server type should the LTM Specialist use?
A.Forwarding (IP)
B.Performance (HTTP)
C.Standard
D.Stateless
E.Performance

[多选题]
Which two locations can be configured as a source for the IOS image in the boot system command?
(Choose two.)
A. RAM
B. NVRAM
C. flash memory
D. HTTP server
E. TFTP server
F. Telnet server

[多选题]
What are three valid reasons to assign ports to VLANs on a switch? (Choose three.)
A. to make VTP easier to implement
B. to isolate broadcast traffic
C. to increase the size of the collision domain
D. to allow more devices to connect to the network
E. to logically group hosts according to function
F. to increase network security

[多选题]
When a DHCP server is configured, which two IP addresses should never be assignable to hosts? (Choosetwo.)
A. network or subnetwork IP address
B. broadcast address on the network
C. IP address leased to the LAN
D. IP address used by the interfaces
E. manually assigned address to the clients
F. designated IP address to the DHCP server

[多选题]141 A virtual server is configured to handle https traffic. The clientssl profile is configured to use a2048-bit RSA key. Due to security requirements, is the LTM Specialist needs to use a 4096-bit RSA key in the future.
What two effects will this change have on the BIG-IP device? (Choose two)
A.Decrease to 20% of licensed TPS
B.Increase of TLS Renegotiation
C.Decrease to 90% of licensed TPS
D.Increase of CPU usage on the BIG-IP device
E.Increased of concurrent connection on client-side

[多选题]
Refer to the exhibit. The two connected ports on the switch are not turning orange or green. What would be
The most effective steps to troubleshoot this physical layer problem? (Choose three.)
A. Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.
B. Ensure that cables A and B are straight-through cables.
C. Ensure cable A is plugged into a trunk port.
D. Ensure the switch has power.
E. Reboot all of the devices.
F. Reseat all cables.

[单选题]
S0./0. on R1. is configured as a multipoint interface to communicate with R2. and R3. in the hub-and-spoke
Frame Relay topology shown in the exhibit. Originally, static routes were configured between these routers
To successfully route traffic between the attached networks. What will need to be done in order to use
RIPv2. in place of the static routes?
A. Configure the no ip subnet-zero command on R1., R2., and R3..
B. Dynamic routing protocols such as RIPv2. cannot be used across Frame Relay networks.
C. Configure the S0./0. interface on R1. as two subinterfaces and configure point-to-point links to R2. and R3..the last octet.

[单选题]
Assuming the default switch configuration which vlan range can be added modified and removed on a cisco
Switch?
A. 2. through 100.1.
B. 1. through 100.1.
C. 1. through 100.2.
D. 2. through 100.5.

[单选题]
Which command enables RSTP on a switch?
A. spanning-tree mode rapid-pvst
B. spanning-tree uplinkfast
C. spanning-tree backbonefast
D. spanning-tree mode mst

[单选题]
Why will a switch never learn a broadcast address?
A. Broadcast frames are never sent to swiches.
B. Broadcast addresses use an incorrect format for the switching table.
C. A broadcast address will never be the source address of a frame.
D. Broadcasts only use network layer addressing.
E. A broadcast frame is never forwarded by a switch.

[多选题]
What are two characteristics of a switch that is configured as a VTP client?(choose two)
A. if a switch that is configured to operate in client mode cannot access a VTP server,then the switchreverts to transparent mode.
B. The local vlan configuration is updated only when an update that has a higher configuration revisionnumber is received.
C. Vtp advertisements are not forwarded to neighboring switches that are configured in vtp transparentmode.
D. When switches in vtp client mode are rebooted,they send a vtp advertisement request to the vtpservers.
E. Vtp client is the default vtp mode
F. On switches that are configured to operate in client mode ,vlans can be created,deleted,or renamedlocally