[单选题]
Which sequence of commands will configured RIPv2. on router B?
A. B(config)# router ripB(config-router)# version 2B(config-router)# end
B. B(config)# router ripB(config-router)# end
C. B(config)# router ripB(config-router)# version 2B(config-router)# end
D. B(config)# router rip version 2B(config-router)# end

[多选题]
When a DHCP server is configured, which two IP addresses should never be assignable to hosts? (Choosetwo.)
A. network or subnetwork IP address
B. broadcast address on the network
C. IP address leased to the LAN
D. IP address used by the interfaces
E. manually assigned address to the clients
F. designated IP address to the DHCP server

[单选题]
Which commands is necessary to permit SSH or Telnet access to a cisco switch that is otherwise
Configured for these vty line protocols?
A. transport type all
B. transport output all
C. transport preferred all
D. transport input all

[多选题]
Which two commands correctly verify whether port security has been configured on port FastEthernet 0./12.
On a switch?(choose two)
A. SW1.#show swithport port-security interface FastEthernet 0./12.
B. SW1.# show swithport port-secure interface FastEthernet 0./12.
C. SW1.# show port-secure interface FastEthernet 0./12.
D. SW1.#show running-config

[单选题]
Which set of commands is recommended to prevent the use of a hub in the access layer?
A. switch(config-if)#switchport mode trunkswitch(config-if)#switchport port-security maximum 1.
B. switch(config-if)#switchport mode trunkswitch(config-if)#switchport port-security mac-address 1.
C. switch(config-if)#switchport mode accessswitch(config-if)#switchport port-security maximum 1.
D. switch(config-if)#switchport mode accessswitch(config-if)#switchport port-security mac-address 1.

[多选题]
Which series of commands will configure router R1. for LAN-to-LAN communication with router R2.? The
A. R1.(config)# interface ethernet 0.R1.(config-if)# no shutdown
B. R1.(config)# interface ethernet 0.R1.(config-if)# no shutdown
C. R1.(config)# interface serial 0.R1.(config-if)# clock rate 560.00.
D. R1.(config)# interface serial 0.R1.(config-if)# no shutdown
E. R1.(config)# router rip
F. R1.(config)# router rip
R1.(config-router)# version 2.

[多选题]
Which two privileged mode cisco ios commands can be used to determine a cisco router chassis serial
Number?(choose two)
A. show inventory
B. show flash:filesys
C. dir flash:|include chassis
D. show diag
E. show controllers

[多选题]
Which router IOS commands can be used to troubleshoot LAN connectivity problems? (Choose three.)
A. ping
B. tracert
C. ipconfig
D. show ip route
E. winipcfg
F. show interfaces

[多选题]
Which two Cisco IOS commands ,used in troubleshooting,can enable debug output to a remote location?(choose two)
A. no logging console
B. terminal monitor
C. logging host ip-address
D. snmp-server enable traps syslog
E. show logging | redirect flash:output.txt

[多选题]
Which two commands can be used to verify a trunk link configurationt status on a given cisco switch?(choose two)
A. show interfaces interface
B. show interfaces interface trunk
C. show interfaces interface switchport
D. show ip interface brief
E. show interfaces vlan

[多选题]
Which two locations can be configured as a source for the IOS image in the boot system command?
(Choose two.)
A. RAM
B. NVRAM
C. flash memory
D. HTTP server
E. TFTP server
F. Telnet server

[单选题]32 RADIUS authentication has been configured on the LTM device. The default remote user access requirements are as shown:
Read only access to the configuration Utility Access to TMOS shell
Which two items need to be configured in this situation? (Choose two)
A.Console access is Advanced Shell
B.Console access is Read Only
C.Default remote user role is Guest
D.In Console access is TMSH
E.Default remote user role is Manager
F.Default remote user role is Operator

[单选题]
There are no boot system commands in a router configuration in NVRAM.What is the fallback sequence
That router will use to find an ios during reload?
A. Flash,TFTP server,ROM
B. Flash,NVRAM,ROM
C. ROM,NVRAM,TFTP server
D. NVRAM,TFTP server,ROM
E. TFTP server,Flash,NVRAM

[单选题]61 An LTM device configured with a management IP address and route and a series of self-IPs and TMM routes. Both management and TMM have a routing entry for 101 10/24 Application traffic is being load balanced and sent to pool member 10.1.1.123 with SNAT Automap and configured.
Which route will the LTM device use?
A.TMM route regardless of the management port status
B.both routes, which will duplicate traffic on both management and TMM interface
C.equal cost multipath load balancing via both routes
D.management route when TMM interface is down or TMM is offline
E.management route regardless of the management port status

[单选题]
A switch is configured with all ports assigned to vlan 2. with full duplex FastEthernet to segment existing
Departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?
A. More collision domains will be created.
B. IP address utilization will be more efficient.
C. More bandwidth will be required than was needed previously.
D. An additional broadcast domain will be created.

[多选题]141 A virtual server is configured to handle https traffic. The clientssl profile is configured to use a2048-bit RSA key. Due to security requirements, is the LTM Specialist needs to use a 4096-bit RSA key in the future.
What two effects will this change have on the BIG-IP device? (Choose two)
A.Decrease to 20% of licensed TPS
B.Increase of TLS Renegotiation
C.Decrease to 90% of licensed TPS
D.Increase of CPU usage on the BIG-IP device
E.Increased of concurrent connection on client-side

[单选题]
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.
OSPF has been configured on the router,as the routing protocol for the network.Which statement about this
Network is true?
A. For the two vlans to communicate,a network statement for the trunk interface needs to be added to theOSPF configuration.
B. For the two vlans to communicate,a network statement for each subinterface needs to be added to theOSPF configuration.
C. Direct inter-vlan communication does not require OSPF.
D. OSPF cannot be used if router-on-a-stick is configured on the router.

[多选题]
Refer to the exhibit. What commands must be configured on the 295.0. switch and the router to allowcommunication between host 1. and host 2.? (Choose two.)
A. Router(config)# interface fastethernet 0./0.Router(config-if)# no shut down
B. Router(config)# interface fastethernet 0./0.Router(config-if)# no shut downRouter(config)# interface fastethernet 0./0..1.Router(config-subif)# encapsulation dot1.q 10.Router(config-subif)# interface fastethernet 0./0..2.Router(config-subif)# encapsulation dot1.q 20.
C. Router(config)# router eigrp 100.
D. Switch1.(config)# vlan databaseSwitch1.(config-vlan)# vtp domain XYZSwitch1.(config-vlan)# vtp server
E. Switch1.(config)# interface fastethernet 0./1.Switch1.(config-if)# switchport mode trunk
F. Switch1.(config)# interface vlan 1.

[多选题]59 A virtual server is configured to handle https traffic. The clientssl profile is configured to use a2048-bit RSA key. Due to security requirements, is the LTM Specialist needs to use a 4096-bit RSA key in the future.
What two effects will this change have on the BIG-IP device? (Choose two)
A.Increase of CPU usage on the BIG-IP device
B.Decrease to 20% of licensed TPS
C.Decrease to 90% of licensed TPS
D.Increased of concurrent connection on client-side
E.Increase of TLS Renegotiation

[单选题]124 An LTM device needs to be configured a virtual server. The application requires SSL encryption from the client to the server and an X-Forwarded-For added by the LTM device. Which virtual server type should the LTM Specialist use?
A.Forwarding (IP)
B.Performance (HTTP)
C.Standard
D.Stateless
E.Performance