更多"Router B1, an internal router in ar"的相关试题:
[单项选择]Which command displays EIGRP-related router activities as they occur?（）
A. TestKing# show ip route *
B. TestKing# debug eigrp route
C. TestKing# debug ip eigrp
D. TestKing# debug ip protocols eigrp
E. TestKing# show ip route eigrp
[单项选择]During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next（）。
A. Because of damaged flash memory, the router will fail the POST.
B. It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.
C. It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.
D. It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.
E. It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.
[单项选择]A router that takes the workstations internal IP address and changes it to another IP address whenit sends the data outside of the network is an example of which of the following?（）
A. NAT
B. IDS
C. NMAP
D. DMZ
[单项选择] R1 is internal to area 1, and R2 is internal to area 2. Subnet 10.1.1.0/24 exists in area 2 as a connected subnet off R2. ABR ABR1 connects area 1 to backbone area 0, and ABR2 c onnects area 0 to area 2. Which of the following LSAs must R1 use when calculating R1's best route for 10.1.1.0/24?（）
A. R2's Type 1 LSA
B. Subnet 10.1.1.0/24's Type 2 LSA
C. ABR1's Type 1 LSA in area 0
D. Subnet 10.1.1.0/24's Type 3 LSA in Area 0
E. Subnet 10.1.1.0/24's Type 3 LSA in Area 1
[单项选择] Router R1 sits inside OSPF area 1. Router R2 redistributes an E1 route into OSPF for prefix 2.2.2.0/24, with external metric 20. Router R22 redistributes an E2 route for the same prefix/length, external metric 10. Under what conditions will R1 choose as it s best route the route through R22?（）
A. R1 will always choose the route through R22.
B. As long as R1's best internal OSPF cost to reach R22 is less than 10.
C. As long as R1's best internal OSPF cost to reach R22 is less than 20.
D. R1 will never choo se the route through R22 if the E1 route through R2 is available.
[单项选择] A network de sign shows area 1 with three internal routers, area 0 with four internal routers, and area 2 with five internal routers. Additionally, one ABR (ABR1) connects areas 0 and 1, plus a different ABR (ABR2) connects areas 0 and 2. How many Type 1 LSAs would b e listed in ABR2's LSDB?（）
A. 6
B. 7
C. 15
D. 12
E. None of the other answers is correct.
[多项选择]Area Border Router （ABR） is a router located on the border of one or more OSPF areas that connect those areas to the backbone network. An ABR will inject a default route into which two types of areas？（）
A. Area 0
B. NSSA
C. Totally stubby
D. Stub
[单项选择]Router A is unable to reach Router B.Both routers are running ios version 12.0.After reviewing the command output and graphic,what is the most likely cause of the problem?（）
A. incorrect bandwidt h configuration
B. incorrect LMI configuration
C. incorrect map statement
D. incorrect IP address
[多项选择] Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）
A. Receive - only
B. Stub
C. Static
D. Summary
E. Connected
F. Dynamic
[多项选择] Router R1 is three router hops away from subnet 10.1.1.0/24. According to various show interfaces commands, all three links between R1 and 10.1.1.0/24 use the following settings: bandwidth: 1000, 500, 100000 and delay : 12000, 8000, 100. Which of the following answers correctly identifies a value that feeds into the EIGRP metric calculation？（）
A. Bandwidth of 101,500
B. Bandwidth of about 34,000
C. Bandwidth of 500
D. Delay of 1200
E. Delay of 2010
F. Delay of 20100
[单项选择] Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured. Which combinations accurately describe the interface under which a feature will be configured?（）
A. PPP on the ATM interface
B. VPI/VCI on the dialer interface
C. IP address on the ATM interface
D. CHAP on the dialer interface
[单项选择] Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（） interface f0/0 mac - address 1111.1111.1 111 ipv6 address 2000::/64 eui - 64 ipv6 address 2001::1/64
A. The next hop is 2000::1311:11FF:FE11:1111
B. The next hop is FE80::1311:11FF:FE11:1111
C. The next hop is FE80::5111:11FF:FE11:1111
D. The next hop is 2001::1
[单项选择]You have a Level 1-only router (Router A) in IS-IS area 49.0001. How does Router A learn how to get to IP prefixes in other areas?（）
A. Router A must have a Level 2 adjacency with the Level 1/Level 2 router in area 49.0001.
B. The Level 1/Level 2 router in area 49.0001 sets the "attached" bit in the Level 1 link-state PDU (LSP) it floods into area 49.0001.
C. The Level 1/Level 2 router in area 49.0001 sets the "attached" bit in the Level 2 LSP it floods into area 49.0001.
D. The Level 1/Level 2 router in area 49.0001 advertises these prefixes into area 49.0001 using a Level 2 LSP it floods into the area.
[简答题]在配EIGRP的时候（frame-relay的NBMA）命令router（config-router）#neighbor 192.168.1.129 是什么意思呢？
[单项选择]Which router or router combination is used to calculate the MPLS traffic engineering tunnel path？（）
A. head-end router and tail-end router
B. middle-point router
C. head-end router
D. tart-end router
E. tail-end router
[单项选择]Which CLI command displays statistical information about a policy called goldservice ?（）
A. show ip interface atm 5/1.1
B. show policy-list goldservice
C. show profile name goldservice
D. show rate-limit-profile goldservice
