[单选题]
Refer to the exhibit. After SwitchB was added to the network, VLAN connectivity problems started to occur.
What caused this problem?
A. Both switches are in sever mode in the same domain
B. The revision number of SwitchB was higher than the revision number of SwitchA
C. SwitchA was not rebooted prior to adding SwitchB to the network.
D. V2.-mode is not enabled.
E. VTP pruning is not activated, so the new paths in the network have not been recalculated.

[单选题]
Refer to the exhibit. After a RIP route is marked invalid on Router_1., how much time will elapse before that
Route is removed from the routing table?
A. 30. seconds
B. 60. seconds
C. 90. seconds
D. 180. seconds
E. 240. seconds

[单选题]
Refer to the exhibit. A network administrator needs to add a new VLAN, named VLAN3., to the network
Shown. Unfortunately, there is not another FastEthernet interface on R1. to connect to the new VLAN3..
Which approach is the most cost effective solution for this problem?
A. Purchase a new FastEthernet module and install it on R1.
B. Replace R1. with a new router that has at least three FastEthernet interfaces.
C. Configure a second switch to support VLAN3. with a VLAN trunk between SW1. and the new switch.
D. Configure a single VLAN trunk between R1. and SW1. and configure subinterface on R1. interface foreach VLAN.
E. Connect another router to a serial interface of R1.. Use a FastEthernet interface on the new router for
VLAN3..

[单选题]
Refer to the exhibit,a network administrator cannot establish a telnet session with the indicated router.Whatis the cause of this failure?
A. A level 5. password is not set
B. The vty password is missing
C. The console password is missing
D. An ACL is blocking Telnet access

[单选题]
Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit
Represents this design, with all hosts configured in the same VLAN. What conclusions can be made about
This design?
A. The design will function as intended
B. Spanning-tree will need to be used.
C. The router will not accept the addressing scheme.
D. The connection between switches should be a trunk.
E. The router interfaces must be encapsulated with the 802..1.Q protocol.

[单选题]
Refer to the exhibit. A network associate has configured the internetwork that is shown in the exhibit, but
Has failed to configure routing properly.
Which configuration will allow the hosts on the Branch LAN to access resources on the HQ LAN with the
Least impact on router processing and WAN bandwidth?
A. HQ(config)# router ripBranch(config)# router rip
B. HQ(config)# router eigrp 56Branch(config)# router eigrp 56.
C. HQ(config)# router ospf 1Branch(config)# router ospf 1

[单选题]
Refer to the exhibit. What statement is true of the configuration for this network?
A. The configuration that is shown provides inadequate outside address space for translation of thenumber of inside addresses that are supported.
B. Because of the addressing on interface FastEthernet0./1., the Serial0./0. interface address will not supportthe NAT configuration as shown.
C. The number 1. referred to in the ip nat inside souce command recerences access-list number 1..

[单选题]
Refer to the exhibit. The company uses EIGRP as the routing protocol. What path will packets take from a
A. The path of the packets will be R3. to R2. to R1..
B. The path of the packets will be R3. to R1. to R2..
C. The path of the packets will be both R3. to R2. to R1. and R3. to R1..
D. The path of the packets will be R3. to R1.

[单选题]
Refer to the exhibit. What can be determined about the router from the console output?
A. No configuration file was found in NVRAM.
B. No configuration file was found in flash.
C. No configuration file was found in the PCMCIA card.
D. Configuration file is normal and will load in 15. seconds.

[单选题]
Refer to the exhibit. Which of these statements correctly describes the state of the switch once the boot
Process has been completed?
A. Only the default VLANs are configured on SwitchA.
B. SwitchA does not have a VTP domain name configured.
C. VTP pruning needs to be enabled on SwitchA.
D. SwitchC needs to have the VTP domain name configured.
E. SwitchB is in transparent mode.

[多选题]
Refer to the diagram. Which three statements describe the router port configuration and the switch portconfiguration as shown in the topology? (Choose three.)
A. The Router1. WAN port is configured as a trunking port.
B. The Router1. port connected to Switch1. is configured using subinterfaces.
C. The Router1. port connected to Switch1. is configured as 10. Mbps.
D. The Switch1. port connected to Router1. is configured as a trunking port.
E. The Switch1. port connected to Host B is configured as an access port.
F. The Switch1. port connected to Hub1. is configured as full duplex.

[单选题]
Refer to the exhibit.How many broadcast domains are configured on switch2.?
A. 5.
B. 20.
C. 4.
D. 1.

[多选题]
Refer to the exhibit.The network administrator requires easy configuration options and minimal routing
Protocol traffic.Which two options provide adequate routing table information for traffic that passes between
The two routers and satisfy the requests of the network administrator?(choose two)
A. a dynamic routing procotol on InternetRouter to advertise summarized routers to CentralRouter.
B. a dynamic routing procotol on CentralRouter to advertise summarized routers to InternetRouter.
C. a dynamic routing procotol on InternetRouter to advertise all routes to CentralRouer.
D. a dynamic routing procotol on CentralRouer to advertise all routes to InternetRouter
E. a static,default route on CentralRouter that directs traffic to InternetRouter.

[单选题]
Refer to the exhibit, Host A pings interface S0./0. on router 3., what is the TTL value for that ping?
A. 253.
B. 252.
C. 255.
D. 254.

[单选题]
Refer to the exhibit. Assume that all of the router interfaces are operational and configured correctly. How
Will router R2. be affected by the configuration of R1. that is shown in the exhibit?
A. Router R2. will not form a neighbor relationship with R1..
B. Router R2. will obtain a full routing table, including a default route, from R1..
C. R2. will obtain OSPF updates from R1., but will not obtain a default route from R1..
D. R2. will not have a route for the directly connected serial network, but all other directly connected
Networks will be present, as well as the two Ethernet networks connected to R1..

[单选题]
Refer to the exhibit. You are connected to the router as user Mike. Which command allows you to see
Output from the OSPF debug command?
A. terminal monitor
B. show debugging
C. show sessions
D. show ip ospf interface

[单选题]
Refer to the exhibit. From RouterA, a network administrator is able to ping the serial interface of RouterB
But unable to ping any of the subnets attached to RouterB. Based on the partial outputs in the exhibit, what
Could be the problem?
A. EIGRP does not support VLSM.
B. The EIGRP network statements are incorrectly configured.
C. The IP addressing on the serial interface of RouterA is incorrect.
D. The routing protocol has summarized on the classful boundary.
E. EIGRP has been configured with an invalid autonomous system number.