更多"[单选题]单板在正常状态下,单板的运行灯和告警灯的状态是( )"的相关试题:
[单选题]当机柜告警灯显示红色闪烁时,表示有()告警产生 。
A.紧急
B.主要
C.次要
[单选题]BORA板卡上的主要告警灯为( )。
A.Ma
B.Mi
C.SDH
D.SY
[单选题]UOMP单板正常运行时,指示灯显示状态正确的是()?
A.OOS灯熄灭
indicator OOS is off
B.OK灯熄灭
indicator OK is off
C.HOST灯熄灭
indicator HOST is off
D.H/S灯1HZ闪烁
indicator H/S is flashing in 1HZ
[判断题]SDH传输设备因监控比较完善且告警种类繁多,因此一般无法从设备面板告警灯指示来判断故障,而应及时与监控中心联系
A.正确
B.错误
[单选题]xGW单板正常运行时()。
A.RUN灯常亮
B.RUN灯长灭
C.RUN灯慢闪(1Hz)
D.RUN灯快闪(5Hz)
[判断题]当单板正常工作时,单板前面板上的RUN灯以1次/秒的频率闪烁、ACT灯常亮、ALM灯和SCAN灯都为熄灭状态。
A.正确
B.错误
[判断题]当MPU单板正常工作时,主用单板前面板上的RUN灯以1次/秒的频率闪烁、ACT灯常亮、ALM灯和SCAN灯都为熄灭状态。
A.正确
B.错误
[判断题]波分设备正常的加电顺序时:首先是将单板置浮插状态,然后使用万用表测试输入电压是否正常,闭合头柜的空开,闭合设备架顶的空开,闭合设备子架的空开,检查风扇的运行状态是否正常,最后将单板依次插入。
After the equipment encounters power failure, the correct power-on order is: Rest the board partially. Use the multimeter to check that the input voltage is normal. If yes, turn on the air switch of the first cabinet, air switch on the top of the equipment, and air switches of the subrack. Check whether the fans run normally. If yes, insert the board. (Liang Zhuo)
A.正确
B.错误
[判断题]xGW GGSN GSU单板正常运行时,RUN灯常亮,ALM灯熄灭。
A.正确
B.错误
[判断题]xGW GGSN GSU单板正常运行时,RUN灯常亮,ALM灯熄灭。
When the GSU board of the xGW GGSN works in normal state, the RUN indicator is always on and the ALM indicator is off.
A.正确
B.错误
[判断题]OTU单板上电后,红绿灯交替闪烁,说明单板本身正常运行,只是网管上没有配置该单板。
If the red and green indicator lights flash alternatively when an OTU board is powered on, it indicates the board is working normally but is not configured in the EMS.
A.正确
B.错误
[判断题]V4 uMAC中SBCJ单板的H/S灯是单板热插拔指示灯,蓝灯常亮表示单板处于非工作状态,可以进行插拔操作。
A.正确
B.错误