更多"[多选题]GGSN新开局需要删除的发货垃圾数据文件目录（）。
Duri"的相关试题:
[多选题]GGSN新开局需要删除的发货垃圾数据文件目录（）。
During setup of a new GGSN office, the following directories that contain trash data should be deleted: ( ).
A.DATA0
B.DATA1
C.VMM
D.CONFIG
[单选题]在GGSN系统割接前，需要检查单板内存，在GGSN中查看内存状态的命令是（）。
Before GGSN system cutover, we need to check board memory. To check the memory status in the GGSN, run the command ( ).
A.show memory
B.show host
C.show processor
D.show hardware
[多选题]GGSN与CG对接时，需要配置的项包括（）。
When the GGSN interconnects with the CG, which of the following items need to be configured?
A.配置CPU组的cgagent地址,每个CPU组都要配置各自的CG Agent地址
Configure cgagent addresses for CPU groups, and each CPU group has its own CG agent address.
B.将 cgagent地址 配置到环回接口地址中
Configure the cgaent address in the loopback interface address.
C.配置与CG通讯的接口地址及路由
Configure the interface IP and route to communicate with the CG.
D.配置CG服务器
Configure the CG server on the GGSN.
E.配置cg-profile,在cf-profile 中配置主备用CG服务器等
Configure cg-profile, and in cf-profile, configure master and slave CG servers.
F.将cg-profile 与apn 关联
Associate cg-profile with the APN.
[单选题]xGW GGSN一般不需要对接的设备是（）。
xGW GGSN generally does not need to connect to ( ).
A.OCS
B.PCRF
C.SGSN
D.HLR
[多选题]在GGSN系统割接前，需要进行主备倒换测试，包括以下（）。
Before cutover of the GGSN system, we need to perform active/standby switchover tests, including: ( ).
A.MPU单板主备倒换测试。
Master/slave MPU board switchover test
B.GSU 单板主备倒换测试.
Master/slave GSU board switchover test
C.CSU 单板主备倒换测试.
Master/slave CSU board switchover test
D.CG双机主备倒换测试.
CG dual-computer active/standby test
[多选题]xGW GGSN割接上线前，需要检查PDP最大空闲时间（idle-time）设置，下面说法正确的是（）。
Before xGW GGSN cutover, need to check the PDP idle-time configuration, which statements are correct?
A.固定设置成1000MIN。
Idle-time should fix to 1000 min.
B.如果新建xGW GGSN是为了替换我司V3 GGSN，则要求xGW的idle-time设置和V3 GGSN保持一致。
If the new GGSN is for replacing ZTE old V3 GGSN, then idle-time value should be same with old V3 GGSN.
C.如果不是替换我司V3 GGSN，则要求和局方现网设置保持一致。
If the new GGSN isn't for replacing ZTE old V3 GGSN, then idle-time value should be same with current network.
D.如果不是替换我司V3 GGSN，局方现网也没有任何GGSN设备，则可根据实际需要配置，推荐1440min。
If the new GGSN isn't for replacing ZTE old V3 GGSN and there is no any GGSN in the current network, then idle-time value should be configured according to the real requirement, and 1440min is for recommendation.
[单选题]xGW GGSN中，需要把手机地址池平均分配到（）上。
In xGW GGSN, addresses in the IP address pool of MS must be assigned to ( ) averagely.
A.GSU Group
B.CU Group
C.SLB Group
D.xDPI Group
[多选题]在V4 GGSN中，需要配置下面哪些接口的loopback地址？（）
On V4 GGSN, the following interfaces should be configured with the loopback address: ( ).
A.GTPC
B.radius client
C.GTPU
D.cgagent
[多选题]V4 GGSN中，需要配置的逻辑接口包括（）。
On V4 GGSN, which logical interfaces need to be configured? ( )
A.Gn
B.Gb
C.Gi
D.Gy
[判断题]xGW GGSN部署license后需要重启MPU才生效。
A.正确
B.错误
[多选题]xGW GGSN采用多地址方式时，哪些组上需要配置IP地址？
When xGW GGSN adopts the multi-address mode, the following groups should configure IP addresses: ( ).
A.GSU Group
B.CU Group
C.SLB Group
D.xDPI Group
[判断题]GGSN上线前，需要检查R_PPPLCPDATA，要求配置成6万。
A.正确
B.错误
