[单项选择]After installing a new video card, the computer loads Windows and continuously reboots. Which of the following would be the FIRST step that a technician should take?（）
A. Run CHKDSK
B. Boot to ERD
C. Run MSCONFIG
D. Go into Safe Mode

[单项选择]After a technician installs a video card, which of the following should the technician configure NEXT?（）
A. Resolution
B. Colors
C. Dots per inch
D. Refresh rate

[单项选择]A technician installs a new video card in a desktop with onboard video. The technician boots the unit but sees no display. The monitor power light is on and the OS seems to be loading. Which ofthe following is the MOST likely cause?（）
A. The display is defective.
B. The video card needs to be flashed.
C. The internal adapter has not been disabled.
D. The new video card is defective.

[单项选择] A technician installed a new video card on a motherboard which has onboard video. When the monitor was plugged into the new card and the power was turned on, a no signal message appeared on the monitor. Which of the following is MOST likely the issue?（）
A. In the BIOS, the onboard video adapter must be disabled.
B. The video resolution is set too high.
C. The LCD panel is defective.
D. The drivers for the new video card must be installed before installing the card.

[单项选择]A technician has replaced a video card with another manufacturer’s video card. The driverinstallation does not complete. Which of the following steps should the technician take FIRST?（）
A. Roll back the driver.
B. Install the original video card and reboot.
C. Delete the monitor.
D. Remove the video card and reboot.

[多项选择] Immediately after adding a new disk to or removing an existing disk from an ASM instance, you find that the performance of the database goes down initially until the time the addition or removal process is completed, and then gradually becomes normal. Which two activities would you perform to maintain a consistent performance of the database while adding or removing disks?（）
A. Define the POWER option while adding or removing the disks
B. Increase the number of ARB processes by setting up a higher value for ASM_POWER_LIMIT.
C. Increase the number of DBWR processes by setting up a higher value for DB_WRITER_PROCESSES
D. Increase the number of slave database writer processes by setting up a higher value for DBWR_IO_SLAVES

[单项选择]After installing a new optical drive into a workstation, which of the following will ask for anacknowledgement?（）
A. IRQ Manager
B. BIOS
C. Device Manager
D. Hardware Compatibility List

[单项选择]After installing a new SATA hard drive the technician notices the drive is hot to the touch and is giving off a slight odor. Which of the following should the technician do? （）
A. Install a larger fan near the hard drive to cool the system.
B. Clean the drive with compressed air and continue to use it.
C. Remove and replace the drive.
D. Apply more thermal compound and reseat the drive.

[单项选择] After testing a new 100BaseTX cable, the technician determines that only pairs 4, 5, 7, and 8 are straight-thru wires. Which of the following MOST likely describes this cable type?（）
A. Crossover cable with open pairs
B. Crossover cable
C. Rollover cable
D. Straight-thru cable with open pairs

[单项选择]After applying a new driver to a NIC, the server reboots and fails to restart. Which of the following is the BEST way to resolve the problem?（）
A. Boot using recovery console and restore the previous driver.
B. Boot the server, press F8 and access last known good configuration.
C. Restore the server using last backup tape.
D. Boot the server with ASR option.

[单项选择]After swapping an internal wireless card on a laptop with an identical model, the technician notices that the wireless does not work. Which of the following would be the MOST likely cause?（）
A. Antennae is not connected
B. Wireless card is defective
C. Drivers needs to be updated
D. OS needs to be updated

[单项选择]After the new technique was introduced, the factory produced ________ tractors in 1998 than the year before.
A. as twice many
B. as many twice
C. twice as many
D. twice many as

[多项选择]After replacing the NIC card of a PC on the LAN, your Cisco switch shows a new MAC address is attached to that port. Which of the following answer choices below correctly describe a MAC address?（）
A. It is a globally unique IP address.
B. It is a globally unique 48 bit address
C. It is provided by the manufacturer of the NIC.
D. It is used as part of the IPX/SPX configuration.
E. It is a logical address.

[单项选择]After the new technology was brought in, this year's production of the cars in our factory is five times ______ it was five years ago.
A. more
B. than
C. what
D. as

[单项选择] While installing a new PCI card the administrator touched the motherboard. While powering on the server, a series of beeps were emitted and the server did not POST. Which of the following could be done to prevent this problem?（）
A. Use ESD equipment.
B. Verify correct voltages are being supplied.
C. Use a system board tester to check for compatibility issues.
D. Install compatible PCI cards

[单项选择]After setting up a new computer, a user states that the mouse and keyboard will not work. Whichof the following is the MOST likely reason?（）
A. The network cable is disconnected
B. The PS/2 connectors are switched
C. The USB connectors are switched
D. The hard drive is unplugged

[单项选择]An administrator installs a new network card in a properly functioning DC. During the Windows boot up process the DC bluescreens. Which of the following is the NEXT step?（）
A. Press F8 and boot to Directory Services Restore Mode.
B. Press F8 and boot to Last Known Good Configuration.
C. Reboot the server again.
D. Press F8 and boot to Safe Mode.

[单项选择]You have to put on a new suit and make yourself look ______.
A. respectable
B. respectful
C. respecting
D. respective