更多"What is the first step of the core "的相关试题:
[单项选择]What is the first step of the core baselining process? ()
A. Verify that the SNMP MIB is supported in the relevant core device.
B. Implement monitoring using SNMP or RMON.
C. Poll and record specific SNMP MIB objects from the device.
D. Implement threshold monitoring using RMON.
[单项选择]What is the final step of the core baselining process?()
A. Implement threshold monitoring using RMON.
B. Implement monitoring using SNMP or RMON.
C. Poll and record specific SNMP MIB objects from the device.
D. Verify that SNMP MIB is supported in the relevant core device.
[单项选择]What step were Bay Area officials going to take regarding e-waste disposal
A. Rally support to pass the stalled bills.
B. Lobby the lawmakers of the California Assembly.
C. Lay down relevant local regulations themselves.
D. Exert pressure on manufacturers of electronic devices.
[单项选择]According to the passage, what step will have the most impact on the recovery at this point
A. Decentralizing of the government.
B. Initiating a permanent tax cut.
C. Dealing with non -performing loans.
D. Encourage investors to put their money into the stock market.
[多项选择]A Catalyst 2950 needs to be reconfigureD.What steps will ensure that the old configuration is erased?()
A. Erase flash.
B. Restart the switch.
C. Delete the VLAN database.
D. Erase the running configuration.
E. Erase the startup configuration.
F. Modify the configuration register.
[单项选择]What is the first step that you would use Cisco Product Advisor for when selecting a router for an Edge solution?()
A. determine types of protocols to be supported
B. determine the environment in which the router will be used
C. select the number of WAN ports required
D. select the number of LAN ports required
[单项选择]During a password recovery, what is the next step after configuring the system to boot into single-user mode?()
A. Reset the root password
B. Press the space bar
C. Type recovery
D. Press the "Enter" key
[单项选择]What is the final step that should take place when characterizing an existing network? ()
A. Form an impression about the network.
B. Prepare and add to the network description.
C. Use traffic analysis to augment organizational input.
D. Perform a network audit.
[单项选择]What is the first step in BGP route selection?()
A. The local router prefers the route with the shortest as-path.
B. The router first verifies that it has a route to the bgp Next Hop IP address.
C. The local router prefers the route from the peer with the lowest peer id address.
D. The local router prefers the route learned from an ebgp peer over a route learned from an ibgp peer.
[单项选择]What is the last step in setting up a Primary Domain Name Server?()
A. Start the named daemon
B. Create the cache file
C. Create the name zone file
D. Create the local IP zone file
[单项选择]What is an important step to take when verifying a newly proposed network security solution? ()
A. Test the design on a pilot network for expected results prior to implementing on the production network.
B. Run a network audit to determine types of traffic in use on the network.
C. Launch campus updates into the production network and monitor impact to see if configuration changes are needed.
D. Create an interruption of data flow to determine test "back-door" access methods.
[多项选择]What are two step needed to define a QoS policy for a traffic class?()
A. determine a minimum bandwidth guarantee
B. determine interfaces to which to apply policy
C. assign priorities to the class
D. configure access control lists
[单项选择]What is the FIRST step in diagnosing a completely dead computer that was working fine the day before?()
A. remove all peripherals and reinstall them one at a time
B. replace the CMOS battery
C. check the AC power cord and verify the power source
D. back up the entire hard drive
[单项选择]What is the first step in setting up a Primary Domain Name Server?()
A. Create the cache file
B. Create the IP zone file
C. Create the named.boot file
D. Create the name zone file