更多"What is the correct sequence of com"的相关试题:
[单项选择]What is the correct sequence of commands to configure and verify SRM with SSO redundancy? （）
A. mode sso, redundancy, show redundancy states
B. show redundancy states, mode sso, redundancy
C. redundancy, mode sso, show redundancy states
D. show redundancy states, redundancy, mode sso
[单项选择]Which of the following commands will display what space is used in /tmp filesystem?（）
A. df -Ik /tmp
B. df -fk /tmp
C. df -Uk /tmp
D. df -Fk /tmp
[单项选择]Which of the following sequence of commands should be used to list the directories and files saved on a mksyst tape that has been rewound and placed in device rmt0?（）
A. tet1 -f /dev/rmt0 fsf 2; restore -xqvf /dev/rmt0
B. tet1 -f /dev/rmt0.1 fsf2; restore -Tvf /dev/rmt0.1
C. tet1 -f /dev/rmt0.1 fsf3; restore Tqvf /dev/rmt0.1
D. tet1 -f /dev/rmt0.1 fsf3; restore -Tvf /dev/rmt0.1
[单项选择]Which of the following sequence of commands extracts the third image from a tape that was created using the backup command?（）
A. tctl -f /dev/rmt0.1 fsf 2 ; tar -xv file3
B. tctl -f /dev/rmt0.0 fsf 3 ; dd if=file3 pf =/dev/mt0.1
C. tctl -f /dev/rmt0.1 fsf 2 ; dd if=/dev/rmt0.1 of=file3
D. tctl -f /dev/rmt0.0 fsf 3 ; dd if=/dev/rmt0.1 of=file3
[单项选择] What is the correct sequence to set up a Virtual I/O Server？（） 1.Boot to SMS 2.Create the VIOS partition 3.Install VIOS software 4.Accept license
A. 4， 2， 1， 3
B. 2， 1， 4， 3
C. 2， 1， 3， 4
D. 1， 2， 3， 4
[单项选择]Which is the correct fallback sequence for loading the Cisco IOS?（）
A. ROM, Flash, NVRAM
B. ROM, TFTP server, Flash
C. Flash, TFTP server, ROM
D. Flash, NVRAM, RAM
[单项选择] What is correct regarding the configuration shown below?（） （1）static route 0.0.0.0/0 （2）qualified-next-hop 172.30.25.1 preference 7 （3）next-hop 172.30.25.5
A. The next-hop 172.30.25.1 is selected because the address has the lowest value.
B. The next-hop 172.30.25.1 is selected because it is listed first.
C. The next-hop 172.30.25.1 is selected because it is the lowest protocol preference.
D. The next-hop 172.30.25.5 is selected because it is the lowest protocol preference.
[多项选择]What are two commands that can be used to configure MBGP for multicast?（）
A. Under the BGP group, configure family inet any.
B. Use the set protocol MBGP command to enable MBGP.
C. Under the BGP group, configure family inet multicast.
D. Use the set rib-group command to copy the multicast routes into inet.1.
[单项选择]What is the proper sequence of evaluation for the SurfControl integrated Web filter solution?（）
A. whitelists, blacklists, SurfControl categories
B. blacklists, whitelists, SurfControl categories
C. SurfControl categories, whitelists, blacklists
D. SurfControl categories, blacklists, whitelists
[多项选择]What are two Cisco IOS commands that can be used to view neighbor adjacencies?（）
A. show ip ospf interfaces
B. show ip ospf protocols
C. show ip ospf neighbors
D. show ip ospf database
[单项选择]What is the correct relative switching priority in a BLSR ring (higher to lower)?（）
A. signal fail, signal degrade, manual switch
B. signal degrade, signal fail, manual switch
C. protection lockout, manual switch, path AIS
D. forced switch, manual switch, signal degrade
E. protection lockout, manual switch, forced switch
[单项选择]What is the correct command to display the current working directory?（）
A. echo $PWD
B. echo $pwd
C. echo $CWD
D. echo $cwd
[单项选择]What does the author think is the correct response to AIDS
A. Fear and contempt.
B. Optimism and bravado.
C. Understanding and compassion.
D. Resentment and avoidance.
[多项选择]What are three key concepts that apply when configuring the EIGRP stub routing feature in a hub and spoke network？（）
A. A hub router prevents routes from being advertised to the remote router.
B. Only remote routers are configured as stubs.
C. Stub routers are not queried for routes.
D. Spoke routers connected to hub routers answer the route queries for the stub router.
E. A stub router should have only EIGRP hub routers as neighbors.
F. EIGRP stub routing should be used on hub routers only.
[单项选择]What is the correct command for creating a new user ID authenticated with LDAP?（）
A. mkuser -R LDAP
B. mkuser -L LDAP
C. mkuser -auth LDAP
D. mkuser -a auth1=LDAP
[单项选择]What is the correct syntax for applying node-specific parameters to each node in a chassis cluster?（）
A. set apply-groups node$
B. set apply-groups (node)
C. set apply-groups $(node)
D. set apply-groups (node)all
[多项选择]What are three correct steps to reset a lost root password?（）
A. Press the TAB key when prompted.
B. Enter boot -p.
C. Enter recovery when prompted.
D. Commit the change.
E. Reboot.
[多项选择]What are two merits of having a correct time setting on each WX/WXC device in a community? （）(Choose two.)
A. Ensures connectivity to the registration server.
B. Allows WX devices to synchronize with one another.
C. Helps in the maintenance of WX devices using WX CMS.
D. Generates accurate and consistent monitoring reports.
[多项选择]What are two results of entering the Switch(config)# vtp mode client command on a Catalyst switch?（）
A. The switch will ignore VTP summary advertisements
B. The switch will forward VTP summary advertisements
C. The switch will process VTP summary advertisements
D. The switch will originate VTP summary advertisements
E. The switch will create, modify and delete VLANs for the entire VTP domain
