更多"Router R1 lists 4 routes for subnet"的相关试题:
[多项选择] The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（） R1# show ip bgp 190.1.0.0/16 BGP routing table entry for 190.1.0.0/16, version 121 Paths: (1 available, best #1, table Default - IP - Routing - Table) Advertised to update - groups: 1 1 2 3 4 1.1.1.1 from 2.2.2.2 (3.3.3.3) Origin IGP, metric 0, localpref 100, valid, internal, best
A. R1 has a neighbor 1.1.1.1 command configured.
B. R1 has a neighbor 2.2.2.2 command configured.
C. The show ip bgp command lists a line for 190.1.0.0/16 with both a n > and an i on the left.
D. R1 is in ASN 1.
[单项选择] Router R1 lists the following output from a show command. Which of the following is true about R1?（） R1# show ip v6 interface f0/0 FastEthernet0/0 is up, line protocol is up IPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456 No Virtual link - local address(es): Global unicast address(es): 2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI] Jo ined group address(es): FF02::1 FF02::2 FF02::1:FF:12:3456
A. R1's solicited node multicast address is FF02::1:FF:12:3456.
B. R1's 2000::4:213:19FF:FE12:3456 address is a global unicast with all 128 bits statically configured.
C. Address FF02::2 is R1's solicited node multicast.
D. R1's solicited node multicast, not listed in this output, would be FF02::213:19FF:FE12:3456.
[多项选择] Router R1 is three router hops away from subnet 10.1.1.0/24. According to various show interfaces commands, all three links between R1 and 10.1.1.0/24 use the following settings: bandwidth: 1000, 500, 100000 and delay : 12000, 8000, 100. Which of the following answers correctly identifies a value that feeds into the EIGRP metric calculation？（）
A. Bandwidth of 101,500
B. Bandwidth of about 34,000
C. Bandwidth of 500
D. Delay of 1200
E. Delay of 2010
F. Delay of 20100
[单项选择]Router R1 sets a route tag for subnet 10.1.1.0/24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?（）
A. Kilobits/seconD
B. Tens of microseconds
C. Cost
D. Hop count
E. No unit is assigneD
[单项选择] Router R1 learns two routes with BGP for prefix 200.1.0.0/16. Comparing the two routes, route 1 has a longer AS_Path Length, bigger MED, bigger Weight, and smaller Loca l PreferencE. Which of the following is true about Router R1's choice of best path for this prefix?（）
A. Route 1 is the best route.
B. Route 2 is the best route.
C. The routes tie as best, but one will be picked to be placed in the routing table based on tiebreakers.
D. Neither route is considered best.
[多项选择] Router R1 and R2 are both configured for HSRP. Which two statements about the HSRP priorities of these two routers are true？（）
A. To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.
B. The default priority of a router is zero （0）.
C. The no standby priority command assigns a priority of 100 to the router.
D. Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.
E. When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.
[单项选择] Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（） interface f0/0 mac - address 1111.1111.1 111 ipv6 address 2000::/64 eui - 64 ipv6 address 2001::1/64
A. The next hop is 2000::1311:11FF:FE11:1111
B. The next hop is FE80::1311:11FF:FE11:1111
C. The next hop is FE80::5111:11FF:FE11:1111
D. The next hop is 2001::1
[多项选择] You have configured router R1 with HSRP， using the standard defaults. Which three statements are true of a default HSRP configuration？（）
A. The Standby hello time is 2 seconds.
B. Two HSRP groups are configured.
C. The Standby track interface priority is 10.
D. The Standby hold time is 10 seconds
E. The Standby priority is 100.
F. The Standby delay is 3 seconds.
[单项选择] Router R1 sits inside OSPF area 1. Router R2 redistributes an E1 route into OSPF for prefix 2.2.2.0/24, with external metric 20. Router R22 redistributes an E2 route for the same prefix/length, external metric 10. Under what conditions will R1 choose as it s best route the route through R22?（）
A. R1 will always choose the route through R22.
B. As long as R1's best internal OSPF cost to reach R22 is less than 10.
C. As long as R1's best internal OSPF cost to reach R22 is less than 20.
D. R1 will never choo se the route through R22 if the E1 route through R2 is available.
[多项选择] Router R1 is configured for HSRP. Which of the following are valid HSRP states on R1？ （）
A. Init
B. Idle
C. Active
D. Standby
E. Established
F. Backup
[单项选择] The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（） D 2000::/64 [90/1422516] via FE80::213:19FF:FE7B:5026, Serial0/0/ 1 C 2000:0:0:1::/64 [0/0] via Serial0/0/1, directly connected L 2000::1:213:19FF:FE7B:5004/128 [0/0] via Serial0/0/1, receive
A. Route 2000::/64 will be redistributed.
B. Route 2 000:0:0:1::/64 will be redistributed.
C. Route 2000:1:213:19FF:FE7B:5004/128 will be redistributed.
D. No routes will be redistributed because of the omission of the subnets parameter of the redistribute command.
[多项选择] Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers. Which of the following is true on R1?（）
A. The show ip ospf neighbors command lists two neighbors off Fa0/0.
B. The show ip ospf neighbors command lists four neighbors off Fa0/0.
C. The show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.
D. The show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.
[多项选择]For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）
A. The router must have one routing protocol configured, but configuration for both routing protocols is not necessary
B. The router must hav e at least one working link connected to each routing domain
C. The redistribute command must be configured under EIGRP to send the routes to OSPF
D. The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
[多项选择] Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）
A. Receive - only
B. Stub
C. Static
D. Summary
E. Connected
F. Dynamic
[单项选择]A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?（）
A. the OSPF route
B. the EIGRP route
C. the RIPv2 route
D. all three routes
E. the OSPF and RIPv2 routes
