更多"Your company has an IPv4 Ethernet n"的相关试题:
[单项选择]Your company has an IPv4 Ethernet network. A router named R1 connects your segment to the Internet. A router named R2 joins your subnet with a segment named Private1. The Private1 segment has a network address of 10.128.4.0/26. Your computer named WKS1 requires access to servers on the Private1 network.The WKS1 computer configuration is as shown in the following table. Network Addresses IPv4 Address 10.128.64.113 Subnet mask 255.255.252.0 Default Gateway 10.128.64.1 The routers are configured as shown in the following table. Router ID Addresses R1 interface 1 R1 interface 2 (To Internet) 10.128.64.1 131.107.108.37 R2 interface 1 R2 interface 2 10.128.64.10 10.128.4.1 WKS1 is unable to connect to the Private1 network by using the current configuration.You need to add a persistent route for the Private1 network to the routing table on WKS1.Which command should you run on WKS1？（）
A. Route add -p 10.128.4.0/22 10.128.4.1
B. Route add p 10.128.4.0/26 10.128.64.10
C. Route add p 10.128.4.0 mask 255.255.255.192 10.128.64.1
D. Route add p 10.128.64.10 mask 255.255.255.192 10.128.4.0
[单项选择]Running both IPv4 and IPv6 on a router simultaneously is known as what?（）
A. 4to6 routing
B. 6to4 routing
C. binary routing
D. dual-stack routing
E. NextGen routing
[单项选择] Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（） ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0
A. OSPF works on F0/0 and S0/0/0 without further configuration
B. OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modE
C. OSPF works with the addition of one command: an router - id command in OSPF router configuration modE
D. OSPFv3 needs at least two more configuration commands before it works on R1
[单项选择]A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOSimage.what function does the router perform next?（）
A. It checks the configuration register
B. It attempts to boot from a TFTP server
C. It loads the first image file in flash memory
D. It inspects the configuration file in NVRAM for boot instructions
[单项选择]Every host and router on the Internet has an IP address, which encodes its
A. host number
B. host number and socket
C. network number
D. host number and network number
[单项选择]Every host and router on the Intemet has an IP address, which encodes its
A. host number
B. host number and socket
C. network number
D. host number and network number
[单项选择]What does a router do if it has no EIGRP feasible successor route to a destination network and the successor route to that destination network is inactive status?（）
A. It routes all traffic that is addresses to the destination network to the interface indicates in the routing table.
B. It sends a copy of its neighbor table to all adjacent routers.
C. It sends a multicast query packet to all adjacent neighbors requesting available routing paths to the destination network.
D. It broadcasts Hello packets to all routers in the network to re-establish neighbor adjacencies.
[多项选择] Your network uses IPv4. You install a server that runs Windows Server 2008 R2 at a branch office. The server is configured with two network interfaces.You need to configure routing on the server at the branch office. Which two actions should you perform？（）
A. Install the Routing and Remote Access Services role service.
B. Run the netsh ras ip set access ALL command.
C. Run the netsh interface ipv4 enable command.
D. Enable the IPv4 Router Routing and Remote Access option.
[多项选择]Your network uses ipv4. You install a server that runs windows server 008 at a brach office. The server is configured with two network interfaces. You need to configure routing on the server at the branch office. Which two actions should you perform? （）
A. Install the routing and remote access role.
B. Run the netsh ras ip set access ALL command.
C. Run the netsh interface ipv4 enable command.
D. Enable the IPV4 router routing and remote access option.
[多项选择]Your network uses IPv4.You install a server that runs Windows Server 2008 R2 at a branch office. The server is configured with two network interfaces. You need to configure routing on the server at the branch office.Which two actions should you perform？（）
A. Install the Routing and Remote Access Services role service.
B. Run the netsh ras ip set access ALL command.
C. Run the netsh interface ipv4 enable command.
D. Enable the IPv4 Router Routing and Remote Access option.
[单项选择]Your company uses DHCP to lease IPv4 addresses to computers at the main office.A WAN link connects the main office to a branch office. All computers in the branch office are configured with static IP addresses. The branch office does not use DHCP and uses a different subnet. You need to ensure that the portable computers can connect to network resources at the main office and the branch office.How should you configure each portable computer？（）
A. Use as tatic IPv4 address in the range used at the branch office.
B. Use an alternate configuration that contains a staticI Paddress in the range used at the main office.
C. Use the address that was assigned by the DHCP server as astatic IP address.
D. Use an alternate configuration that contains a staticI Paddress in the range used at the branch office.
[单项选择]your company uses DHCP to lease IPv4 addresses to computers at the main office. A WAN link connects the main office to a branch office. All computers in the branch office are configured with static ip addresses. The branch office does not use DHCP and uses a different subnet. You need to ensure that the portable computers can connect to network resources at the main office and the branch office. How should you configure each portable computer?（）
A. Use a static IPv4 address in the range used at the branch office.
B. Use a alternate configuration that contains a static IP address in the range used at the main office.
C. Use the address that was assigned by DHCP as a static IP address.
D. Use an altermate configuration that contains a static IP address in the range used at the branch office.
[单项选择] A BGP router has the following configuration： protocols{ bgp{ export[policy-1 policy-2 policy-3]； }} policy-options{ policy-statementpolicy-2 { termget-statics{ fromprotocol static； thenaccept； } termreject-all { thenreject； } } policy-statementpolicy-1 { termget-aggregate { fromprotocol aggregate； thenaccept； } termreject-all { thenreject； } } policy-statementpolicy-3 { termget-ospf { fromprotocol ospf； thenaccept； } termreject-all { thenreject； } } } Which policy term is evaluated first when exporting routes？（）
A. get-ospf
B. reject-all
C. get-statics
D. get-aggregate
