更多"A Fibre Channel fabric (or Fibre Ch"的相关试题:
[单项选择]A Fibre Channel fabric （or Fibre Channel switched fabric， FC-SW） is a switched fabric of FibreChannel devices enabled by a Fibre Channel switch. Fabrics are normally subdivided by Fibre Channel zoning. Each fabric has a name server and provides other services. Higher redundancy over FC-AL，P2P.Which path selection protocol is used by Fibre Channel fabrics？（）
A. OSPF
B. RIP
C. FSPF
D. VSANs
[单项选择]Which statement about Fibre Channel communications is correct?（）
A. It operates much like TCP.
B. Flow control is only provided by QoS.
C. It must be implemented in an arbitrated loop.
D. Communication methods are similar to those of an Ethernet bus.
E. N_Port to N_Port connections use logical node connection points.
[单项选择]Which of the following provides Fibre Channel over IP and FCIP Tunneling Service for distance extension, which can enable cost-effective and manageable metro and global business continuity solutions?（）
A. IBM System Storage SAN80B-4
B. IBM System Storage SAN Volume Controller (SVC)
C. IBM System Storage SAN04B-R Multi-Protocol Router
D. IBM System Storage TS7650GProtecTIER Deduplication Gateway
[单项选择]Fibre channel requires which of the following elements?（）
A. FC Initiator
B. Multi-Mode fibre
C. Physical Adapter
D. Fibre Target Management Agent
[单项选择] A customer intends to implement a Fibre Channel SAN at the production site. Replication will take place over a 10 kilometer Ethernet connection to a second site; however, only IP storage connectivity currently exists at the second site. Which is the most appropriate method of replication in this situation?（）
A. FC routing
B. FCoE connection
C. FC-IP tunneling
D. multi-protocol router
[单项选择]A customer has a Fibre Channel switch residing in a configuration where both production and test data coexist. Which of the following is the simplest method for ensuring that the two types of data do not flow through the same port?（）
A. VLAN
B. zoning
C. trunking
D. LUN masking
[单项选择] A system has two configured fibre channel cards, one of which, fsc0, has failed and must be replaced. Which command should an administrator use to remove the card device and attached child devices?（）
A. rmdev -Rdl fcs0
B. rmdev -cdl fcs0
C. rmdev -cdl fscsi0
D. rmdev -Rdl fscsi0
[多项选择]Fibre Channel, or FC, is a gigabit-speed network technology primarily used for storage networking.Fibre Channel is standardized in the T11 Technical Committee of the InterNational Committee for Information Technology Standards (INCITS), an American National Standards Institute (ANSI) Caccredited standards committee.Which two of these correctly describe Fibre Channel?（）
A. supports multiple protocols
B. works only in a shared or loop environment
C. allows addressing for up to 4 million nodes
D. provides a high speed transport for SCSI payloads
[单项选择]Fibre channel requires which of the following elements？（）
A. FC Initiator
B. Multi-Mode fibre
C. Physical Adapter
D. Fibre Target Management Agent
[多项选择]Which two Fibre Channel features are not supported in Cisco Nexus 5500 and Nexus 5000 platforms？ （）
A. port security
B. fabric binding
C. IVR
D. port tracking
E. FICON
[多项选择]Fibre Channel， or FC， is a gigabit-speed network technology primarily used for storage networking.Fibre Channel is standardized in the T11 Technical Committee of the InterNational Committee forInformation Technology Standards （INCITS）， an American National Standards Institute （ANSI）Caccredited standards committee. Which two of these correctly describe Fibre Channel？ （）
A. supports multiple protocols
B. works only in a shared or loop environment
C. allows addressing for up to 4 million nodes
D. provides a high speed transport for SCSI payloads
[多项选择]Which two of these correctly describe Fibre Channel? （）
A. supports multiple protocols
B. works only in a shared or loop environment
C. allows addressing for up to 4 million nodes
D. allows addressing for up to 8 million nodes
E. provides a high speed transport for SCSI payloads
F. may stretch to a distance of up to100 km before needing extenders
[多项选择]Which two statements about MPLS label-switched paths (LSPs) are true? （）
A. LSPs are bidirectional.
B. LSPs are unidirectional.
C. LSPs must follow the IGP's shortest path.
D. LSPs can follow paths other than the IGP's shortest path.
[单项选择] You are an administrator of a switched network and your goal is to reduce some of the administrative overhead on your network. You plan on achieving this by configuring a new VLAN for each department in your network. However, you need to share the VLAN information across numerous switches throughout your network. Which of the following would allow you accomplish this?（）
A. STP
B. GVRP
C. SNMP
D. VTP
E. DHCP
[单项选择]Which path selection protocol is used by Fibre Channel fabrics?（）
A. IVR
B. VoQ
C. FSPF
D. VSANs
E. SANTap
[单项选择]What is a Label-Switched Path?（）
A. a traffic engineered path
B. another name for a Frame Relay PVC
C. a bidirectional path through a network
D. a unidirectional path through a network
[单项选择]When is a switched network that is running the Spanning Tree Protocol considered to be fully converged?（）
A. when all switches have the same BID as the root switch
B. when all switches have received the MAC address of each neighboring switch
C. when every enabled switch port has been assigned a unique identifier
D. when every operating switch port is in either the blocking or forwarding state
E. when all switches are in either client, server, or transparent mode
[单项选择]In a switched environment, what does the IEEE 802.1Q standard describe?（）
A. the operation of VTP
B. a method of VLAN trunking
C. an approach to wireless LAN communication
D. the process for root bridge selection
E. VLAN pruning vlan
[单项选择]When an IP packet is Layer 3-switched from a source in one VLAN to a destination in another VLAN,which field in a packet will be rewritten? （）
A. Layer 2 TTL
B. Layer 3 TTL
C. Layer 3 source address
D. Layer 3 transport protocol
E. Layer 3 destination address
