更多"The EIGRP configuration in the Glen"的相关试题:
[多项选择]Which of the following are methods EIGRP uses to initially populate (seed) its EIGRP topology table, before learning topology data from neighbors？（）
A. By adding all subnets listed by the show ip route connected command
B. By adding the subnets of working interfaces over which static neighbors have been defined
C. By adding subnets redistributed on the local router from another routing source
D. By adding all subnets listed by the show ip route static command
[多项选择] Examine the following configuration on Router R1. R1's show ip route 172.16.4.1 command list s a route with outgoing interface S0/1/1. Host 172.16.3.3 uses telnet to connect to host 172.16.4.1.What will Router R1 do with the packets generated by host 172.16.3.3 because of the telnet,assuming the packets enter R1's F0/0 interface?（） interface Fastethernet 0/0 ip address 172.16.1.1 255.255.255.0 ip policy route - map Q2 ! route - map Q2 permit match ip address 101 set interface s0/0/1 ! access - list 101 permit tcp host 172.16.3.3 172.16.4.0 0.0.0.255
A. The packet will be forwarded out S0/0 /1, or not at all.
B. The packet will be forwarded out S0/0/1 if it is up.
C. The packet will be forwarded out S0/1/1 if it is up.
D. The packet will be forwarded out S0/1/1 if it is up, or if it is not up, out s0/0/1.
E. The packet will be forwarded o ut S0/0/1 if it is up, or if it is not up, out s0/1/1.
[单项选择]A router has EIGRP configured as the only routing protocol. How does EIGRP respond if there is no feasible successor route to a destination network and the successor route fails?（）
A. It immediately sends its entire routing table to its neighbors.
B. EIGRP sends a Hello packet to the DR to inform it of the route failure.
C. It automatically forwards traffic to a fallback default route until a successor route is found.
D. It sends queries out to neighbors until a new successor route is found.
E. It places the route in holddown until LSA updates inform it of a new route to the network.
[单项选择] Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）
A. R1 has been configured with an ip default- network 2.0.0.0 command.
B. R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.
C. R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
D. Another router has been configured with an ip default - network 2.0.0.0 command.
E. Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
[单项选择] During BGP configuration on a router that has peered with other BGP speakers, the BGP command aggregate-a ddress 172.32.0.0 255.255.252.0 is issued. However, the peers do not receive this aggregate network in BGP advertisements. Also, the router does not have this aggregate network in its BGP table. Which option indicates a possible reason this command did not cause the router to advertise the aggregate network to its peers?（）
A. Interface NULL 0 is likely shutdown.
B. The next hop IP address must be a loopback address.
C. The BGP command no auto - summary is missing.
D. The BGP command no synchronization is missing.
E. Subnets of 172.32.0.0/22 do not exist in the BGP table.
F. The IGP running on this router does not have network 172.32.0.0/22 installed.
[单项选择]Within the L2TP LNS configuration of the router, where is the PPP authentication method specified?（）
A. profile
B. remote host
C. aaa domain-map
D. l2tp destination profile
[单项选择]Which configuration command allows the router to utilize a RADIUS server to authenticate incoming Telnet users?（）
A. aaa new-model
B. aaa telnet login
C. telnet authentication login
D. authentication telnet login
[单项选择]Which configuration command enables the router for SNMP？（）
A. snmp-client
B. snmp-server
C. snmp-clientenable
D. snmp-serverenable
[多项选择] On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and 10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH. Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）
A. show ip route
B. show ip eigrp topology
C. show ip ospf topology
D. show ip eigrp topology 10.1.1.0/24
[单项选择] Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all. Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?（）
A. R1 limi ts EIGRP to around 250Kbps on DLCI 102
B. R1 limits EIGRP to around 250Kbps on DLCI 104
C. R1 limits EIGRP to around 150Kbps on every DLCI
D. R1 does not limit EIGRP because noWAN bandwidth control has been configured
[单项选择] The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（） interface loopback 1 ip address 192.168.1.1 255.255.255.255 interface tunnel 2 ipv6 address 2002:C0A8:10 1::1/64 tunnel source loopback 1
A. Automatic 6to4
B. Manually configured tunnel
C. ISATAP
D. GRE
[单项选择]What does a router do if it has no EIGRP feasible successor route to a destination network and the successor route to that destination network is inactive status?（）
A. It routes all traffic that is addresses to the destination network to the interface indicates in the routing table.
B. It sends a copy of its neighbor table to all adjacent routers.
C. It sends a multicast query packet to all adjacent neighbors requesting available routing paths to the destination network.
D. It broadcasts Hello packets to all routers in the network to re-establish neighbor adjacencies.
[简答题]在配EIGRP的时候（frame-relay的NBMA）命令router（config-router）#neighbor 192.168.1.129 是什么意思呢？
[单项选择]Which command displays EIGRP-related router activities as they occur?（）
A. TestKing# show ip route *
B. TestKing# debug eigrp route
C. TestKing# debug ip eigrp
D. TestKing# debug ip protocols eigrp
E. TestKing# show ip route eigrp
[单项选择] The output of s how ip eigrp topology on Router R1 shows the following output, which is all the output related to subnet 10.11.1.0/24. How many feasible successor routes does R1 have for 10.11.1.0/24?（） P 10.11.1.0/24, 2 successors, FD is 2172419 via 10.1.1.2 (2172423/2 8167), Serial0/0/0.1 via 10.1.1.6 (2172423/28167), Serial0/0/0.2
A. 0
B. 1
C. 2
D. 3
[单项选择] Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enable
A. RIPng will be enabled on no interfaces.
B. RIPng will be enabled on one interface.
C. RIPng will be enabled on two interfaces.
D. RIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.
[多项选择] Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（） interface f0/0 ipv6 address 2345:0:0:8::1/64
A. 2345:0:0:8::1
B. 2345:0:0:8:0:FF:FE11:1111
C. FE80::8:0:FF:FE11:1111
D. FE80:0:0:8::1
[单项选择]A router learns about a remote network from EIGRP, OSPF, and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network（）。
A. The router will use the static route.
B. The router will use the OSPF route.
C. The router will use the EIGRP route.
D. The router will load balance and use all three routes.
