更多"The function of the after-cooler in"的相关试题:
[单项选择]An after-cooler installed between the turbocharger and the cylinder air inlet （）
A. increases the density of the air
B. decrease the density of the air
C. increases the specific heat of the air
D. decreases the specific heat of the exhaust
[单项选择]What is the function of the after-cooler installed in the diesel engine air intakes system?（）
A. Decrease the air density
B. Increase the exhaust temperature
C. Decrease the lube oil temperature
D. Increase the air density
[单项选择]Intercoolers installed on starting air compressors, reduce the possibility of（）
A. dust entering the high pressure stage
B. lube oil carbonization
C. discharge pulsations
D. inter-stage vapor lock
[单项选择]Temperature control valves installed in the jacket cooling water system of a diesel engine modulates the rate of water flow through the （）.
A. cooling water pump
B. nozzle cooling passages
C. cylinder jackets
D. heat exchanger
[单项选择]The circular steel structure installed around the propeller of a towboat is the（）.
A. nozzle
B. shroud
C. strut
D. hood
[单项选择]Why are removable sleeves installed on centrifugal pump shafts?（）
A. They make it easier to replace the pump shaft packing
B. They can be economically replaced as they wear out
C. They can be removed when it is necessary to lighten the weight of the pump
D. They increase the strength of the shaft
[单项选择]Three access ports have been installed and configured to a small office.What term defines the wireless topology?（）
A. IBSS
B. BSS
C. ESS
D. SSID
[单项选择]Kort nozzles are installed around the propellers of some vessels to（）.
A. Increase the thrust of the propeller
B. Protect the propeller from striking sawyers
C. Prevent the propeller from striking barges towed on the ship
D. Prevent the propeller from touching bottom in low water
[单项选择]Fins are installed on the generating tube surfaces in waste heat boilers to （）.
A. prevent soot fires in the exhaust system
B. prevent exhaust gas erosion of the tubes
C. increase the velocity of exhaust gas flow
D. increase the rate of heat transfer
[单项选择]Emergency generator is installed on board mainly to （）
A. connect to the busbar when the load increasing
B. supply power specially to charging panel
C. be put into operation during the ship arriving at or leaving port
D. ensure the power supply to critical equipment after the main switchboard out of power
[单项选择]The purpose of the safety relief valves installed on an auxiliary boiler is to （）.
A. relieve excess fuel oil pressure during the “off” fire cycle
B. admit water to the dry pipe
C. throttle the forced draft fan output for proper combustion
D. reduce excess steam pressure in the boiler
[单项选择]Overgreasing of ball bearings installed on pumps will result in （）.
A. smoother pump operation
B. overheating of the bearing
C. reduced corrosion in the bearing
D. increased pump capacity
[单项选择]Air receivers installed in starting air systems are to be （）.
A. cylindrical in shape with service connections located at the top and bottom
B. opened and made available for inspection during biannual inspections provided
C. with automatic drain traps for the removal of moisture
D. so installed as to make the drain connections effective under extreme conditions of trim
[单项选择]Zinc rods are installed in the refrigeration system （）.
A. liquid strainer
B. liquid receiver
C. saltwater condenser
D. evaporator
[单项选择]Bottom blow valves are installed on auxiliary water-tube boilers to （）
A. completely drain the boiler in an emergency
B. prevent sludge from forming in the drum
C. remove floating impurities from the boiler water surface
D. remove settled solids from the water drum
[单项选择]Have you installed the new software?（）
A. Installed.
B. Uninstalled.
C. No, not yet.
D. Yes, not yet.
[单项选择]A single fitting installed in a pipeline that either blanks off the pipe or allows a full flow passage of a liquid through the pipe is referred to as a（）.
A. blind flange
B. pivot coupling
C. quick-release coupling
D. spectacle flange
[单项选择]Backfire flame arrestors are installed on（）.
A. fuel tanks
B. spark plugs
C. carburetors
D. distributors
