更多"The discharge flow of a reciprocati"的相关试题:
[单项选择]A mixed-flow pump is a （） pump classified by the working principle.
A. self priming
B. positive displacement
C. reciprocating
D. impeller
[单项选择]When starting a reciprocating pump, the inlet valve should be （）.
A. closed
B. opened fully
C. cracked open
D. partly open
[单项选择]A reciprocating pump belongs to （） according to its working principle.
A. injector pumps
B. positive displacement pumps
C. centrifugal pump
D. centripetal pumps
[单项选择]Before starting a reciprocating, steam-driven pump that has been idle for a period of time, you should （）.
A. open the steam line mot valve
B. drain the steam cylinder
C. close the steam cylinder drains
D. open the liquid cylinder drains
[单项选择]The reciprocating pump can’t draw water from a tank may be caused by （）.
A. leaky pipe
B. opened inlet valve
C. too much water in tank
D. None of the above
[单项选择]The discharge head of a centrifugal pump will vary directly with the （）.
A. change in impeller diameter
B. square of the impeller diameter
C. cube of the impeller diameter
D. impeller efficiency for large changes in the size of the impeller
[单项选择]The discharge side of every fire pump must be equipped with a（）.
A. gate valve
B. pressure gauge
C. check valve
D. strainer
[单项选择]The boiler feed pump discharge pressure is higher than the steam drum pressure to （）.
A. ensure feed water flow into the boiler
B. keep the steam drum pressure high
C. prevent water hammer in the feed line
D. help the feed water flash to steam
[单项选择]The pump discharge pressure will be considerably higher than the pressure at the （）.
A. pump entry branch
B. outlet pipe
C. impeller
D. None of the above is true
[单项选择]The valve on the discharge side of a cargo pump on a tank vessel will usually be a（）.
A. butterfly valve
B. spectacle valve
C. check valve
D. globe valve
[单项选择]An increase in the fuel injection pump discharge pressure can be caused by a/an （）
A. leaking delivery valve
B. excessive bearing end play
C. plugged injector spray hole
D. increased plunger stroke
[单项选择]When starting a centrifugal pump, the discharge valve should be （）.
A. closed
B. opened fully
C. cracked open
D. partly open
[单项选择]Before liquid can flow into a pump, the air in the suction line must be （） sufficiently to cause the liquid to flow into the suction chamber.
A. filled
B. evacuated
C. compressed
D. charged
[单项选择]A centrifugal pump produces flow with a resulting discharge head by energy conversionIt is typical for the energy conversion to follow the order of （）.
A. mechanical energy to kinetic energy to potential energy
B. mechanical energy to potential energy to kinetic energy
C. potential energy to mechanical energy to kinetic energy
D. kinetic energy to mechanical energy to potential energy
[单项选择]If a bilge pump failed to build up discharge pressure, you should check for （）.
A. excessive water in the bilges
B. a clogged suction strainer
C. oil in the bilges
D. All of the above
[单项选择]In （） pump a closed discharge valve will not cause excessive pressure to build up.
A. gear
B. vane
C. screw
D. centrifugal
[单项选择]A centrifugal pump attempting to develop flow against a closed discharge valve has a/an （）.
A. capacity of 0%
B. efficiency of 100%
C. internal slippage of 0%
D. shut off horsepower rating of 100%
[单项选择]Because the flow rate of supply water pump is too large, oily water separator does not work wellWhich of the following is not the reason?（）
A. the monitoring equipment is out of order
B. separating effect becomes bad
C. inner wall is contaminated
D. separating effect becomes bad and inner wall is contaminated
